DISCUSSION 1. Compare between the practical and theoretical results for input and output voltages. 2. What design parameters of the full wave single-phase rectifier? 3. When you design 10kW rectifier, what type of rectifier must be use? Why? J 4. Desigh a Carbon dioxide laser power supply, if the voltage across dicchórge tuhe is 12kYolt and the current pass through discharge tube is

DISCUSSION 1. Compare between the practical and theoretical results for input and output voltages. 2. What design parameters of the full wave single-phase rectifier? 3. When you design 10kW rectifier, what type of rectifier must be use? Why? J 4. Desigh a Carbon dioxide laser power supply, if the voltage across dicchórge tuhe is 12kYolt and the current pass through discharge tube is

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
1.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. 2.) A 12 V rms ac supply is connected to the primary winding of a transformer with a turns ratio of 0.052. Calculate the rms secondary voltage given a voltage regulation of 4.0% 3.)Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor.
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
2. A single-phase single-diode (half wave) rectifier is connected to a 240 V, 50 Hz AC supply. Neglecting the diode volt drop, derive the instantaneous load current equation, determine the current waveform, mean load voltage, and the mean load current for a load of a. Pure resistor of 5 Ohm b. An inductance of 0.1 H in series with 10 Ohm resistor. (clue : B= 265° or 14.72 ms)
Design a controlled half wave rectifier circuit to produce an average of 30 V across a 250 ohm load resistor from a 220 Volt max 50 Hz AC source. Determine the power absorbed by the resistance. What would be the average voltage value if diodes were used in this circuit? no chat GPT, only hand written please otherwise leave a DOWNVOTE
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
A single-phase center-tapped rectifier has an R-L of R= 20 0, L = 50mH, and a 240 V ac 50 Hz source voltage. Determine: i. The average and rms currents of the diodes and the load. ii. The rms and average 50 Hz source currents. iii. The power absorbed by the load. iv. The supply power factor.
An ohmic resistive load connected to the output of a single phase uncontrolled full-wave (with diode) AC / DC rectifier and the output voltage average value Va is obtained. Same resistance single phase full wave, controlled (with thyristor) AC / DC was connected to the output of the rectifier and the average value Vb of the output voltage was obtained. Va = 1.7 Vb Find the trigger angle of thyristors.
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification); iv. The current diode, Id. v. The frequency of the output signal, Fout. vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
What condition should be followed to achieve discontinuous current mode operation in fully controlled rectifiers ? a. large L/R value b. large inductance value c. rated inductance value d. small L/R value