Choose at least 3 methods and solve for the support reactions of the beam shown. Draw the shear andmoment diagram.Given Values:Note that El is constant.L= 1.35 metersP1= 635 NewtonsP2= 735 NewtonsW1= 453.5 NewtonsW2= 907 NewtonsW2W2B.C21211.5L1.5L21

P1=635 NP2=907 NW1=453.5 N = 453.52(1.35)w1=272.22 N/mW2=907 N 12(w2)(1.5)(1.35)=907 Nw2=895.8 N/m…

Choose at least 3 methods and solve for the support reactions of the beam shown. Draw the shear and moment diagram. Note that El is constant. Given Values: L= 1.35 meters P1= 635 Newtons P2= 735 Newtons W1= 453.5 Newtons W2= 907 Newtons P2

Choose at least 3 methods and solve for the support reactions of the beam shown. Draw the shear and moment diagram. Note that El is constant. Given Values: L= 1.35 meters P1= 635 Newtons P2= 735 Newtons W1= 453.5 Newtons W2= 907 Newtons P2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rectangular beam of width 100 mm is subjected to maximum shear force of 60 kN. The corresponding m...

A: Given data- Width of the beam b=100 mmshear force S=60 kN=60,000 Nmaximum shear stress τmax=4 N/mm2T...

Q: Find the area of a piece of land with an irregular boundary as follows: Station Offset D...

Q: What will be the depth of a beam that is 20 cm wide and is subjected to shearing force of 10,000 kg....

A: The given question is related with solid mechanics . In this question we are provided with value of ...

Q: what are the "needs analysis" that are required for designing a water flow sensor, what are the cons...

A: Needs analysis is the formal process that sits alongside Requirements analysis and focuses on the hu...

Q: Design reinforcement for a slab-built integrally with its supports and consists of equal spans of 5m...

A: A concrete slab is a flat layer of a building, such as a home or a business, a factory, or a flat. T...

Q: THE INTERNAL FORCE OF MEN mpression, include a negative sign two (2) decimal places only witho (4.67...

Q: Determine the maximum negative bending moment at point B due to a concentrated live load of 50 kN an...

Q: Determine the maximum negative bending moments at point B due to a concentrated live loads of 50 kn ...

Q: Active earth pressure per meter length on the retaining wall with a smooth vertical back as shown in...

Q: following data : ) Qty. of soft water required per hour = 25,000 litres (ii) Hardness present in raw...

Q: The state plane stress at a point is represented by the stress element below. Determine the stresses...

A: Radius of the circleR=(σx-σy2)2+τxy2R=(90+602)2+202R=77.62 MPAσAVG=σx+σy2=90-602σAVG=15mpaσ1=15+77.6...

Q: To make a peg adjustment, the following notes were taken: Wye lev...

Q: hows a cylinder of 4 on ABCD [Take : Yw

Q: Deflection of Beams Use Conjugate Beam Method Given: X - 274 у-74 а-8 b - 4 с- 9 Y kN 2 m X kN 2 m B...

Q: A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter...

A: Pinlet - Pthroat = 28KPa V(velocity) = Q(discharge)/A(area)

Q: Provide at least five possible attachments for a hydraulic excavator and define the use of each iden...

A: Five possible attachments for a hydraulic excavator are: 1. Hydraulic Breaker 2. Excavator Grapple 3...

Q: Ans. P = 9.212 kN 3. A square aluminum bar is to support a load of 40 kN on a length of 3 m. Assumin...

Q: Engineering Mechanics DETERMINE THE INTERNAL FORCE OF MEMBER EF FROM THE FIGURE BELOW. Note: for ...

Q: oil (0.88) oil (0.88) Hg (SG=13.6) 320mm-

Q: what is the commonly used shape of columns in residential house? AUTOCAD

A: Most widely used shape of column in residential building is rectangula shape. Rectangular shape is ...

Q: Please show complete soln a) If two pressure gauges are fitted at tapping points, one at the throat...

A: Given data in question Diameter of pipe and throat Mercury as manometric fluid Specific gravity of...

Q: A concrete dam retains water to a height of 9 m. It has rows of sheet piling at both heel and toe wh...

Q: CONSTANT-HEAD PERMEABILITY TEST METHOD and FALLING HEAD PERMEABILITY TEST METHOD When it comes ...

Q: The steel cylinder has a specific weight of 490 l6/ft and acts as a plug for the 1 ft long slot in t...

Q: The diagonal members in the center panels of the truss shown are very slender and can act only in te...

Q: A 75mmx150mm wooden beam is simply supported at the ends and has a span of 6m. It supports a point l...

Q: Q.6 A beam has solid circular cross-section having diameter d. If a section of the beam is subjected...

A: given-solid circular section dia=dshear force F

Q: The acceleration of a particle traveling along a straight line is a = -si m/s?, where s is in meters...

A: Answer We are given acceleration of the particle a = 14s12 m/s2 Given condition If v=0, s=3.2 m w...

Q: Active earth pressure per meter length on the retaining wall with a smooth vertical back as shown in...

Q: Question 8 The rigid, horizontal slab is attached to two identical copper rods. There is a gap A = 0...

Q: Determine the pressure at depth of 12.3 m from top of water level

A: The given question is related with fluid mechanics . In this question we are provided with value of ...

Q: 3. Compute azimuths of all lines for a closed traverse ABCDA that has the following balanced angles ...

A: To find out the azimuth of BC, CD and DA.

Q: 5 kN 2 m E. A 6 kN 8 kN 2 m 2 m

A: Determine force in member BD using method of section

Q: with no end contractions were to replace the triangular weir, what would be the required H in

Q: The properties of six different clayey soils are shown below based from a series of Atterberg Limit ...

Q: 5 kN 2 m C E. A 6 kN 8 kN 2 m 2 m 2 m

Q: Compute azimuths of all lines for a closed traverse ABCDA that has the following balanced angles to ...

A: To Find :- Azimuth of traverse lines

Q: A water supply pipeline crossing a wide river is to be supported by a flexible wire cable with an al...

A: The given data is shown below: Tensile load=40000 kgWeight of pipe=100 kg/mTotal length of pipe=100 ...

Q: Given data: Degree of saturation3D0.285 Water content%3D0.22 Specific gravity=2.67 Find void ratio

A: The given question is related with geotechnical engineering . In this question we are provided with ...

Q: A septic tank is to be constructed to serve for a family of 8 persons. The size of a septic tank is ...

A: Given data- Total number of people=8Size of the septic tank=2300 mm×1500 mm×1500 mm

Q: THIS TOPIC IS RELATED TO GEOTECHNICAL ENGINEERING Reduction in void ratio is a measure of the effect...

Q: A crate of mass 45 kg is pushed along a floor with a force of 16 N for a distance of 6 m. Calculate ...

A: The given question is related with mechanics topic. In this question we are provided with value of m...

Q: Find the radius of the second curve in a reversed curve, given the following details: • first Pl is ...

A: Given, PI1=33+50.15PI2=40+16.70∆1=75°20'L∆2=83°50'RR1=375 ft

Q: kindly help me with this simple problem hope you could help me thank you! Illustrate label and des...

Q: A gravity dam made of concrete is shown in Figure 2.a. From Figure 2.b, cars can pass through at the...

Q: A retaining wall with a vertical smooth back is 8 m high. It supports a cohesionless soil (y = 19 kN...

Q: 450 mm 750 mm Ce= 40 mm db = 25 mm fe'= 28 Mpa fy 414 Mpa Mu max = 1000 KN-m a. determine the actual...

Q: 4. The structure in the figure is composed of two rigid bars (AB and CD) and two verti rods made of ...

Q: 1. Wid th of the gale being aG m 4m. Oil SG = 0-62 a. Det the hydrostahié trie of the Gognid ig the ...

Q: The structure in the figure is composed of two rigid bars (AB and CD) and two vertical rods made of ...

Concept explainers

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.

Question

Choose at least 3 methods and solve for the support reactions of the beam shown. Draw the shear and
moment diagram.
Given Values:
Note that El is constant.
L= 1.35 meters
P1= 635 Newtons
P2= 735 Newtons
W1= 453.5 Newtons
W2= 907 Newtons
W2
W2
B.
C
21
21
1.5L
1.5L
21

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Fixed end moment

VIEW

Step 3 Distribution Factor

VIEW

Step 4 Moment Distribution Table

VIEW

Step 5 Support reactions

VIEW

Step 6 SFD and BMD

VIEW

Step by step

Solved in 6 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Example Determine the bar forces and reactions in the truss shown in Figure 11.8a. Note that AE is constant for all bars. R₁4 30' E 20' 9 kips D 20 Rc=Xc ↑ Acv=0 C
D 140 mm in the trusses analyies experiment we got the strain Reading as, B Loaden) 5train AB strain AC 5train BC (EM) (EM) (EM) O 469 1117 1116 50 465 1115 1126 100 463 1110 1131 150 458 1095 1139 200 453 1085 250 450 1080 calcute the force in each member; F= πTd²x ExE 4 d = 5.985mm E = 210 GN/m² B W с 1148 t 155
Figure la shows a truss with pin supports at A and roller supports at B. All members have varying cross sectional areas as shown. E = 29,000 ksi for all members. Figure 1b shows the solved reactions and forces for the real system forces (in kips). The virtual forces (in kips) developed are shown in the boxes. 20 kips 20 kips 20 kips 20 kips 15 kips 15 kips 0 -0.8 D (6 in?) (8 in?) -18.75 (8 in?) (6 in?) B 15 kips A 15 -0.8 В A 16 ft 8.75 kips 31.25 kips Figure 1a Figure 1b N.T.S. N.T.S. a) Determine if the truss is statically determinate or statically indeterminate and to what degree. b) Use the compatibility conditions and the constitutive law and find the force in member AD. (zu1 9) (uI 9) 12 ft > -8.75 -0.6 9'0- 02- 12 ft
For the simply supported beam shown in Figure 4, calculate the reactions at supports. y p + *0.5m I J L L L L L U 15 KN B e D 2 m 2m * Figure 4 3
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
Question: Determine the reactions at the support A of the beam shown in the Figure. 3okv loke m
Question 2 A truss structure as shown below needs to be analyzed. It was studied that stiffness method is most suitable. As an engineer, a. Find the members stiffness АР, 5 b. Determine the global stiffness Matrix c. Find the displacements at the nodes. d. Find the reactions at the supports. CR, 10 EV, 10 AN, 5 400 kN 4 800 kN 3 m (1) 4 m 1, 3.
QUESTION 1 METHOD OF CONSISTENT DEFORMATION. For the frame shown below, determine the reactions at the supports (MA Ax Ay Cy) using Method of Consistent Deformation. El is constant. 500 lb/ft В 3 k A 10 ft 10 ft C
I can't find the section effect diagram and support reactions B is equal to 1 B=1
Q.3: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as shown in Figure below. For steel has a 15 mm circular cross section, shearing modulus G = 83 GPa. For aluminum has a 20 mm circular cross section, shearing modulus G = 28 GPa Determine :The two torques at supports A and C 500N.m B 2m 1.5m steel aluminum di=15 mm di=20 mm G = 83 GPa. G = 28 GPa.
1. Answer the following questions in the truss shown. a. Find the support reaction at the roller in the Figure. b. For the truss shown in the figure , determine the number of joints. c. Find the axial force in member AB as shown in the figure using the method of joints. d. What is the axial force in member EF as shown in the figure using the method of joints?
Use the stiffnes method to determine all the displacement components at node 2 and all the reactions including the internal reactions at node 2. Show all calculations. Draw the Bending Moment Diagram of the frame. Show all calculations. Node 1 and 3 are fixed. L3 = 6.5m L4 = 13m w = 6.0 kNm P = 20 kN I = 300 x 10^6 mm^4 A = 10 x 10^3 mm^2 E = 200 GPa