Design reinforcement for a slab-built integrally with its supports and consists of equal spans of 5m. The service live load is 4.78 kPa and f'c = 21 MPa. Steel is specified for yield strength of 420 MPa. Use 12mm diameter bars for main bars and 10mm for temperature bars.

Design reinforcement for a slab-built integrally with its supports and consists of equal spans of 5m. The service live load is 4.78 kPa and f'c = 21 MPa. Steel is specified for yield strength of 420 MPa. Use 12mm diameter bars for main bars and 10mm for temperature bars.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(QI-B) Put (True) or (False) for the following, 1. In doubly reinforcement of RC beams. it the provided steel reinforcement ratio should be more than the maximum reinforcement ratio as specified in ACI 318-19 requirements of singly beam. 2. In working strength method, allowable tensile stress in (280 MPa) yield strength deformed steel bars used in reinforced cement concrete is (140 MPa). 3. In ultimate strength method, the factor of safety for bending strength is more than the shear strength of the beam, when the beam designed as under-reinforced section. 4. As ACI 318-19, the minimum nominal cover specified for beam is 25 mm? 5. Live loads are always taken 100% when it used in calculations of long Rerm deflection of reinforced concrete beams.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 20 kips, w = 4.8 kips/ft, LAB = 4.2 ft, Lec = 4.2 ft, and Lco = 16.0 ft. Determine the magnitude of the maximum bending stress in the beam. P B C D LAB LBC LCD Answer: Omax = i ksi
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 24 kips, w = 2.2 kips/ft, LAB = 4.2 ft, LBC = 4.2 ft, and Lcp = 15.8 ft. Determine the magnitude of the maximum bending stress in the beam. P B LAB LBC Answer: Omax tel i |C * ksi W LCD X
1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: kindly check below answer
Y1
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Calculate the design bending strength for the doubly reinforced rectangular section where A’s = 2500 mm2 f’c= 30 MPa & fy = 350 MPa if As =8500 mm2
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm bars.A. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: Kindly double check your answer