CH9 P2. When tightening a bolt, you push with an angle of 83.0 on a wrench with a force of 167.0N at a distance of 0.119m from the center of the bolt (a) How much torque are you exerting in newton.meters (relative to the center of the bolt)7 (b)Take the average radius of the bolt head to be 17.7mm. What is the average force on the bold head when you tighten it? Answer to 35igFigs with proper units answer (a) Answer (b)

CH9 P2. When tightening a bolt, you push with an angle of 83.0 on a wrench with a force of 167.0N at a distance of 0.119m from the center of the bolt (a) How much torque are you exerting in newton.meters (relative to the center of the bolt)7 (b)Take the average radius of the bolt head to be 17.7mm. What is the average force on the bold head when you tighten it? Answer to 35igFigs with proper units answer (a) Answer (b)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

pivot X 30° F As shown in the diagram above (viewed from above), force F of magnitude 882 N is exerted on a rod which is pivoted about its center a distance 0.7 from the pivot. Calculate the torque exerted by force F. Express your answer in N*m and round to the nearest tenth (1 decimal). Enter a negative answer for a clockwise torque and a positive answer for a counterclockwise torque.
The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are rotated through 180°? Assume the radius of the bicycle wheel is 12.7 inches. The bicycle will travel approximately (Round to the nearest tenth.) in. C -1.95 in 4.21 in
Determine the mechanical advantage of the following pulley system. Provide your answer in kg to 4 decimal places. В A Answer:
There is a kindof antique bicycle in which the radius of the rear wheel is one-tenth of the front wheel. When this bicycle was used to travel 200 feet, the rear wheel rotated 90 times more than the front wheel. What is the diameter of the rear wheel in inches?
A belt is to transmit 50 kW power to a machine. The sheave is 10 inches in diameter and turns at 1200 rpm, while the larger sheave turns at 500 rpm. Determine the length of belt in mm.
1 0 Calculate the total volume of the cylindrical component below (not to scale): L1 D1- D1 = 1.12 cm D2 = 0.71 cm D3 = 1.58 cm L1 = 18.68 cm L2 = 15.36 cm L3=13.77 cm L4 = 9.77 cm Answer: Check L2 L3 L4 D2- What is the volume of the cylindrical component? (State your answer in S.I. units (m³), accurate to 3 significant figures) D3
A technician states that the master cylinder has a piston radius of .75" and the caliper piston has a diameter of 1.25" If he pushes the master cylinder with a force of 15 ft/lbs and the master cylinder input shaft travels 2.5%, what is the force at the caliper piston? (in decimal form rounded to three decimal place, sood 250
The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin connected at O, A, B, and C. 4 The dimensions are OA-240 mm, AB-240 mm, BC-650 mm and theta-20deg. The plane drives at constant velocity on the airport runway. The weight of the plane is 25 kN. C decimal. D OA BC B AB o Find the magnitude of the force in the pin A (magnitude). Give your answer in kN with one
In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e angle a at which slider B reaches the extreme right position. Write your answer in degrees but do not write the unit. 7 cm. Find the value of 7777 x. Answer: DELL
I tried the degree both 51 and 50.99 but it is incorrect. Plz help.
2) USE THE METHOD OF SECTIONS TO FIND THE MAGNITUDE AND DIRECTION OF THE FORCE IN BAR CD SHOWN BELOW IN Fig 1.2 D -600lb -800lb B 4 7' 4' H. G 8' 8' Fig 1.2
(200 lb)(0.6 ft)+PABcos30°(0.75 ft)PAB==0184.752 lb Can you please show all the numbers in this equation so that it would be clear how you get the 184.752 lb in the end.