Can the Mohr’s circle be used to determine the principal strains, the maximum strains, the maximum in-plane strain or the strains on an arbitrary plane?

Q: Q4/ The corner of a 0.4m_ 0.3m 9.2 m cubic element is displaced to point C, whose coordinates are…

A:

Q: Consider steel B is a cylindrical sample with original length 40mm and subjected to 15700N.…

A: Option b is correct.

Q: True strain is based upon (A) Original c/s area (B) Final c/s area (C) Average c/s area (D)…

A: In the case of engineering stress and strain curve , the curve is dependent upon the gauge length of…

Q: For some metal alloy, a true stress of 345 MPa (50040 psi) produces a plastic true strain of 0.02.…

A: The step by step solution for this problem is shown below.

Q: Can the normal strain on the free surface of a body be measured in aparticular direction using an…

A: The magnitude of the strain measures using the device strain gauge. Strain gauge works on a…

Q: Due to the Poisson effect, is the element also subjected to an out-of-plane strain?

A: The Poisson ratio is the measure of lateral strain and the longitudinal strain. The ratio obtains…

Q: What are the elastic modulus (E) and the Poisson's ratio () used to indicate? 2. Illustrate the…

A: The elastic modulus (E) and Poisson's ratio are two important parameters used to describe the…

Q: How can the principal normal strains and maximum in-plane shear strain be determined?

A:

Q: 40-mm sides glass polymer fibers composite cube shown in Figure.2. The Glass polymer fibers aligned…

A: INTRODUCTION: The internal force per unit area of the cross-section is termed as stress. Stress is…

Q: (c) Describe what is represented by Poisson's ratio and show what it measures with the aid of a…

A: the significance of poisson's ratio is to be described and a relationship between axial stress and…

Q: From the tensile stress-strain behaviour for a casted iron as shown in the following curve. Please…

A: Given data: The original length of the specimen is L = 100 mm. The tensile stress is σt = 300 MPa.

Q: Which of the following is an accurate statement? (A) The lateral strain is greater than the axial…

A: Axial strain :-The change in length over the original length of a material along its axis is…

Q: The original length of a piece of metal is 400 mm, this piece has pulled in tension with stress of…

A:

Q: Identify the material that has a maximum modulus of elasticity from the following stress-strain…

A: Material A has higher modules of elasticity.

Q: A material is subjected to a general state of planestress. Express the strain energy density in…

A: E is the modulus of elasticity, G is the modulus of rigidity, and ν is the Poisson’s ratio these are…

Q: In order to obtain the residual stress, is it necessary to know the strain in each segment due to…

A: Residual Stress: They are the stresses that are present in the specimen, after the removal of loads.…

Q: calculate the following: 1-modulus of elasticity 2-tensile strength 3-the ductility in % of…

A:

Q: A plate (Fig. Qla) is subjected to uniform stresses o, and o, only. This loading gives rise to…

A: It is required to evaluate given statement for given loading

Q: Take longitudinal strain 0.02

A: Given data : Longitudinal strain εL=0.02 Poisson's ratio μ=0.5   To find : Lateral strain

Q: Stress strain behavior of a cast iron with a diameter of 15.8mm and gauge length of 60.80mm is shown…

A: Given Stress strain graph L =60.8 mm Diameter 15.8 mm to find Percentage elongation

Q: How can the strain-energy density be determined?

A: Strain energy is defined as the energy absorbed by any member when work done by any load deforms…

Q: At a point on a component, the strain is measured as two perpendicular direct strains, E and Ey, and…

A:

Q: 4. A cylindrical metal wire 2m long is loaded in tension, causing it to extend 15mm. Calculate the…

A: GivenL=2m∆L=15mm=0.015m

Q: sce M13.5 Strain measurement with rosettes Ea 500 µE Eb -200 με %3D Ec 250 με 30° 30° I| ||

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: A 21.00-m steel beam with 6.000 cm × 6.000 cm cross-section is supported at opposite ends by two…

A:

Q: What strain will be produced by a stress of 20 x 10° N/m?, for a given modulus of elasticity 100GPA.…

A: Stress = 20 × 10 6 N/m2 modulus of elasticity = 100 Gpa =100×109N/m² Stress = Strain × modulus of…

Q: If a rubber material is deformed as shown in the following figure. determine the normal strain along…

A:

Q: Is the normal strain sometimes stated in terms of a ratio of length units?

A: The normal strain is defined as " it is the ratio of change in length to the original length: under…

Q: Q1-. A 1m long metal is stretched so that it increases in length incrementally in four passes by an…

A:

Q: When a homogeneous isotropic material is subjected to a state oftriaxial stress, the strain in each…

A: In a homogeneous material, all the properties are the same at each and every point of the material.…

Q: For a linear elastic isotropic material, prove that a state of plane stress result in a strain field…

A: When an amount of load act on an object, then the force applied by the molecules of the object so…

Q: Poisson's ratio is defined as

A: Given data : Lateral strain is denoted by εLT Longitudinal strain is denoted by εL   Required :…

Q: A man leg can be thought of as a shaft of bone 1.2 m long. If the strain is 1.3x10-4 when the leg…

A: Given : Strain in leg, e = 1.3×10-4 Length of bone of leg, L = 1.2 m

Q: 1. Define: Strain Energy. Write the formula to calculate (i) the strain energy due to axial loads…

A:

Q: the longitudinal strain is 0.003 and the poisson's ratio is 0.3, calculate the transverse strain.

A:

Q: What is plane strain condition? List all zero stress and strain components in plane strain.

A: Plane strain conditions:In the direction perpendicular to the plane, the stress and strain…

Q: Extension Compression Determine the engineering strain "e" and the true strain “e" for each of the…

A: