Calculate to the correct number of significant figures. (9443+45-9.9)x8.1x10^6
Q: Homework: Following are the results of a sieve analysis: 10 20 Sieve No. 40 60 100 200 pan Mass of…
A: Given : table
Q: Why is it important to determine the slopes and displacements?
A: Slope – when ever any load is applied on the beam due to its elastic properties it bend in very…
Q: Choose the right answer: a)The lower the quality of the surface finish, the less of area of a…
A:
Q: In sheet metal parts, the minimum bending radius is dependent on which of the following elements? a.…
A: given: In sheet metal parts, the minimum bending radius is dependent on which of the following…
Q: The effect of temperature on the crystallization of a material is given below. Calculate the…
A: Given is Effect of temperature on the crystallization of the material To determine…
Q: 1.6 What is the density of a metal sample if a15.12-g sample is added into a graduated cylinder…
A: The density of the material sample can be known if one can able to find mass and volume of the…
Q: Q3/ the table below show the properties of three materials suggest to applicate as tooth filling…
A: In the given parameters, K refers to thermal conductivity of the material. It represents the ability…
Q: A manufacturer of plastic traffic cones sells the cones at a wholesale cost of £8 pounds per cone.…
A:
Q: Forging process is suitable for mass production. Select one: True False
A: Forming process: It is a mechanical process in which the plastic deformations is done for the…
Q: 1.10.4 [5] Assume a fabrication process improves the yield from 0.92 to 0.95. Find the defects per…
A:
Q: Select all answers that are correct. Which of the following statements explain why solids have…
A: The atoms of the solid are rigidly bounded and allowed only vibrate within its own small ranges but…
Q: Indicate the reasons and effects that deviates the normality graph, explain with examples. 4F mun 4F
A: Given: Here,→Given Normal distribution is non symmetric about its mean→It is positively skewed
Q: 3.. Discuss Archard's theory of wear
A: To find:- Archadas theory
Q: For a pitted specimen designated as A-3,B-3, and C-5(Figure 7.3), sketch the pit density, indicate…
A: The given standard chart provides a way in which pitting can be described. The given specimen is A-3…
Q: Circles of a metal are being punched that will be later stamped into coins. The metal has a shear…
A: Given The shear strength of metal is τ=32575 psi. The thickness of the sheet is t=2.1 mm. The…
Q: According to distortion energy theory, Octahedral shear stress corresponding to yielding in uniaxial…
A: Answer is 0.471 σo
Q: Determine the indentation diameter and the surface area of indentation of a copper material…
A: Given: The test force, P = 8.3 kN The diameter of the steel ball. D = 9 mm The Brinell hardness…
Q: 9.6 - Perform the following reclassification:
A: To do :+ Reclassification
Q: QUESTION 22 A hydraulio metal stamping machine must produce 12.000 parts per 8 hour shift The force…
A: Given data The machine has to produce 12000 parts in an 8 hour shift. Efficiency = 72% Maximum force…
Q: Two previously undeformed specimens of the same metal are to be plastically deformed by reducing…
A: The hardest specimen will be the one that has experienced the greatest degree of cold work. So,…
Q: (a) Find the minimum load factor of safety for fatigue based on infinite life (present the…
A: “Since you have posted a question with multiple sub-parts, we will solve first subparts for you. To…
Q: titanium bar 9.4mm in diameter with a gauge length of 50mm is pulled in tension to failure. After,…
A:
Q: Which of the following material has minimum Indentation diameter? Select one: Mildsteel Aluminium…
A: Indentation dimeter is inversely proportional to the hardness of the material.
Q: Use the least total cost lot-sizing method to determine the quantity to order with the first order…
A: Given Data: To find the number of units to be ordered to cover the needs for specific periods using…
Q: A boundary-lubricated bearing is typically a smooth hollow cylinder through which a shaft passes…
A: Given: L/D = 0.5
Q: The total load to the crusher in lbs/hr is A. 6300
A: Given Data- B ( The product) - 1800 sbs/hr 14 - mesh screen From screen analysis the commulative…
Q: The casting shown is to be made in cast iron using a wood pattem. Perform the calculations required…
A: Given , dimensions of the casting 500x300x80 mmi Machinery allowance 3mm/sideii Shrinkage…
Q: Based on the plotted curve, calculate the average/tangent Young's modulus and Poisson's ratio for…
A: we have to evaluate the poisson's ratio & youngs modulus
Q: parameters except: Question 8 options: a. Time b. Pressure
A: Curing process do not depends on size of the components.
Q: The following figure demonstrates the pressure acquired form a direct extrusion process versus the…
A: Given: Extrusion process
Q: (U) A blanking die must be designed to blank the part outline shown in Figure 4 jall dimensions in…
A:
Q: A blanking operation is to be performed on 2.0 mm thick cold rolled steel (half hard). The part is…
A: Given, Blank diameter =Db = 75 mm Thickness = t = 2 mm For cold rolled steel, Clearance allowance =…
Q: 2.) Two previously undeformed specimens of the same metal are to be plastically deformed by reducing…
A: Given Data: The original diameter of the circular specimen is, d0=18 mm. The deformed diameter of…
Q: Describe the theory Tresca yield criterion?
A: Theories of failures relates different failure criterions with the properties of the materials such…
Q: A rotating bar made of steel with ultimate strength of 600 MPa is subjected to a completely reversed…
A: Given that ,Sut=630 MPa=630=N/mm2Se=300MPa=300N/mm2N=90000 cycles
Q: Calculate the number of finished goods (output) or N for the manufacturing process illustrated in…
A: From the above given diagram, the number of inputs The semi-finished goods after Die Casting,…
Q: The demand and forecast for February are 12000 and 10275, respectively. Using single exponential…
A: Given:Demand for feb, D=12000forecast for feb, F=10275smoothening coefficient, μ=0.25
Q: A solid cylinder of diameter 100 mm and height 50 mm is forged between two frictionless flat dies to…
A: Option d is correct
Q: A compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet…
A:
Q: Forging process is suitable for mass production. Select one: True False
A: Forging:- Forging is the process in which material is shaped by the application of the…
Q: Q3/ the table below show the properties of three materials suggest to applicate as tooth filling…
A: Thermal conductivity measures the ability of a material to conduct heat. For example, the high value…
Q: Define Hooke's Law, Limit of Proportionality and Yield Point
A: To define Hooke's Law, Limit of Proportionality and Yield Point
Q: 5.) Two previously undeformed specimens of the same metal are to be plastically deformed by reducing…
A: For circular → di = 18 mm , dF = 15.9 mmFor rectangular → Initial dimension = 20 x 50…
Q: pany that produces x thousand A type and y thousand B type annually will have annual expenses C(x,y)…
A: Profit = Income - expense=8x+5y - ( 5x2 – 4xy + 3y2 – 18x + 20) =26x+5y- 5x2 -3y2 +4xy -20
Q: 5. A copper wire with length 0.5 m was subjected to a tension experiment, the wire was tensioned to…
A: As per policy, we can solve the first one question from multiple questions.
Q: 32. Initial volume of the billet is same final volume in forging process. Select one: True False
A:
Q: 17.28 For each of the metals listed in the following + table, compute the Pilling-Bedworth ratio.…
A:
Q: Q3/ the table below show the properties of three materials suggest to applicate as tooth filling…
A: As we know, the physical property of the tooth filling:- -It can be a low value of the thermal…
Calculate to the correct number of significant figures. (9443+45-9.9)x8.1x10^6
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
- I tried 33.7oC and also 50.517oC but it still says it is incorrect (view attached screenshot). I appreciate your efforts, but unfortunately it says it is still wrong. Any more ideas of what the correct answer might be? I really want to understand how to solve this problem correctly. Thank you!using the sine bar technique, find the value of the angle for the given data: the stacked height was composed of the following values, 30, 20, 5, 2 and 1.1 mm. The length of the sine bar is 150 mm. Support your answer by sketch.Answer the questions below, (Insert the numerical value only, do not use ,+, *, or /) The Relative error for your answer should be less than 0.01, which means if the answer was 50, then the error should not exceed 50*0.01= ±0.5! if the answer was 230, then the error should not exceed 230*0.01= +2 3! if the answer was 2.31467*10^ 3, then you should enter this value: 0.00231467, not this 0.0023 !!!! K2 K1 M1 fv1 M2 f(t) if M1=4, M2=3, fv1=7, K1=4, K2=6. Find the state equations for the translational mechanical system shown in Figure. [d/dt(r1) d/dt(v1) [(1.1) (1.2) (1.3) (1.4) rl (1)] (2.1) (2.2) (2.3) (2.4) (3.1) (3.2) (3.3) (3.4) [(4.1) (4.2) (4.3) (4.4)] vl * f(t)$$ $$ d/dt(r2) d/dt(v2) r2
- Question 3 The figure below shows a stepped shaft produced from a turning process on a Lathe Machine. Discuss the step-by-step process of producing the stepped bar and the tools used. During the discussion, mention the components that you are using to archive a certain dimension. The initial bar provided is L = 250 mm and D = 50mm. Required dimensions are lengths: Labels Lengths in mm Diameters in mm A 54 66 46 D 34 46 116 K 186 230 .は.05 -Kは.05- -は.05- -It .05- A B B Note: Procedure required (Narrative): Set-up a . .chuck on the ., insert the bar in the. .and tighten using a . Take out a ., insert it in the ..and lock in position. Select a a ............. with . machine. Select the speed using the . place it in the . .and set the height adjustment with the . Remove the. .., insert it in the . .and lock in position. Ensure.. „and replace it with are taken every time you work on the .on the.Round number to three significant figures. 1.548937 x 10^7Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C'(4, 0, 5), find (a) the angle between AB and AC, (b) the angle between BA and BC, and (c) the angle between CA and CB. (a) ZBAC = 29.9 (b) ZABC 42 (c) ZACB = 95.225 Submit Question X X > 8
- Nup ==0.6+ 0.387 (675586) (1+( 1+ 9 0.559 16 0.7228 8 27 = 13.1 How to get 13.1 by calculator? I try many times buy my answer not the same.The figure below shows a stepped shaft produced from a turning process on a Lathe Machine. Discuss the step-by-step process of producing the stepped bar and the tools used. During the discussion, mention the components that you are using to archive a certain dimension. The initial bar provided isL = 250 mm and D = 50mm. Required dimensions are lengths: Labels Lengths in mm Diameters in mm 54 66 C 46 34 46 116 186 230 は.05- K仕.05 Jt.05 は.05- A B B Note: Procedure required (Narrative): Set-up a .chuck on the.. ., insert the bar in the .. .and tighten using a .. . Take out a . ., insert it in the .......and lock in ......., place it in the insert it in the. position. Select a .and set the height adjustment with the. . Remove the. ..and replace it with . .and lock in position. Ensure. on the. a... .. .with .are taken every time you work on the machine. Select the speed using the .P=(2x0.625x65000)/(60) =1354 so it's not 1330. so the answer is wrong
- I have been stuck on this problem for while thar area is 779.1 mm^2 sigma_x is 120.6497159 sigma_y is 0 and tau_xy is 0. Beta is 20 degreesWhy Fsin40= 80*9.8 how can I know is Fsin40already answered in bartleby. please do not copy! STATICS OF RIGID BODIES (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS AND FBD LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 3 DECIMAL PLACES. BOX THE FINAL ANSWERS.) Let a = 11.66 mm