Calculate the value of 6.520kg/7.87 x 10^-3 m^3

Q: Problem H: For Problem Number 29 &30. Given the data below determine the required. k,= 10Scm/sec k3=…

A:

Q: 1. For the area shown, calculate the radii of gyration about the x- and y-axes. - 60– 30 25 90 20…

A:

Q: determine the shape factor and the plastic zone length sigma_{y} = 30OMPA 350 mm 200 mm 8 mm y 200…

A: Objective: To obtain Shape factor and Fully plastic moment of the given built up section.…

Q: can you explain why in solving for d the 2.5in was divided by 2

A: Given:- The overall depth of the beam = 30 in The concrete cover = 2.5 in  To determine:- Why for…

Q: The moment of inertia of the profile shown below, in relation to the x axis, is valid:

A: Solution- First we have to calculate centroid axis in horizontal direction. Moment of individual…

Q: diameter 35 Cm- -> Ain 30cm th=30) (water> high Cm 30cm 5cm aiameter)

A:

Q: 2. An archaeologist took some measurements on the unique mountain he had found. He sets two points X…

A: Given: Distance between X and Y =928 m Angle of elevation of peak of mountain from point X=47 ° 10'…

Q: Consider the area shown in graph. Suppose that a=4 m, b=6 m, and k=3/8 m^-1. Locate the centroid y…

A: a=4 m, b=6 m, To find:The centroid y of the shaded area.

Q: Moment of inertia

A: Given: A rectangular section having depth, d= 2 m witdth, b= 2 m   To calculate: Moment of inertia

Q: What will be the metacentric height of a rectangular block having dimension 6 × 3 × 1.5 m if the…

A: Given - Dimention of rectengular block = (6×3×1.5) m Submerged height = 0.8 m To find - The…

Q: A steel tape with a cross-sectional area of 0.03 sq. cm is 50.00 m long under a pull of 5 kg when…

A:

Q: Situation 4: A W6x25 has a length of 5.3 m. Fy= 248 MPa. The properties are given below. Properties…

A: Le = kL = 0.8 x 5.3 m = 4.24 m = 4240 mm

Q: How did you find Hf = 24.5? Also, you went from 112.1 to 142.1?

A: To Determine :- How 112.1 changed to 142.1 in the solution and How to get Hf = 24.5 m

Q: Assign random values ​​to stakeholders A and B in tons and c-d-e in meters and calculate the support…

A: CONSIDERING A=10 TONS, B=10 TONS b=1m, c=2m, e=2m, d=3m VK+VL=5HK=53HK=8.66 tonsmoment about k is…

Q: Problem 2. A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported…

A:

Q: A 30 m steel tape weighing 1.45 Kg is of standard length under a pull of 5 Kg,supported for full…

A:

Q: Try to observe and analyze this figure. Kindly state what can you tell.

A: There are three force acting find…

Q: How to get the 0.716N (from the underlined value on the picture)?

A:

Q: For this, the interior angles εa =297μ, εb =800μ, εc = 471μ, heights are read with a drawing rosette…

A:

Q: A plate of 0.025 mm distant from a fixed plate, moves at 50 cm/s and requires a force of 1.471 Pa to…

A:

Q: Compute the moment of inertia about x-axis. Y r= 4m 10 m 4 m O 88.37 m^4 O 445.25 m^4 195.04 m^4 O…

A: Given Composite Area with dimensions. To Determine Moment of Inertia about x-axis.

Q: The angular velocity of the left disk is given as a function of time by wA = 4.7 + 0.16t rad/s.…

A:

Q: A line’s length has been measured repeatedly on different occasions. The following are the results…

A: Given:- The results obtained after repeated measurement of the line are:- 1st measurement record =…

Q: . A Geodetic Engineer used a 100 m. tape in measuring a line and recorded to be 1000.05 m long. The…

A:

Q: It is required to determine the vertical angle of the rod that is above the theodolite instrument.…

A: Given Inclined distance = 55m Vertical distance = 45 m Required Vertical angle and horizontal…

Q: can the value of B=0.09m ??? it's not possible

A:

Q: Use Gauss-Seidel iteration to solve: (Do only ten iterations) 2х + у + 4z %3 6 5х + 2у — 2z %3D16 х…

A:

Q: • Solve the following problem for Mp by Kinematic and Static Method? 2.0 m B 20/kN M₂ 4.0 m 2.0 m с…

A:

Q: 15. Compute the resultant of the three forces shown in the figure. 400 N • 948.27 N • 894.32 N •…

A:

Q: Two pipes A and B, each of § cm diameter branch off from a point 1 in a pipe line and rejoin at 2.…

A:

Q: 6 kN 2 kN/m 4 kN A 3 m 1.5 m 1.5 m

A:

Q: Q2. Find the locations and values of all the forces (ton) acting on the quadrant of the circle AB?…

A:

Q: Snown below is the ved section of a ship in a form of a parabolic segment (b=2 m, n=4 m) if the sea…

A: Answer  Calculation of 'FH' We know that horizontal component of force on curved surface is given by…

Q: A jet having a diameter of 50.95mm and a velocity of 15.95m/s is deflected 60.95degree by a curved…

A: To determine the force exerted on the given circular vane by the jet of water.   Given, Diameter of…

Q: 2. An archaeologist took some measurements on the unique mountain he had found. He sets two points X…

A:

Q: A homogenous thin plate of mass 2kg and radius r = 3? cm is shown. If d is 4cm, which of the…

A: Given data,  d = 4 cm Mass (M) = 2 kg

Q: Figure (a) shows a channel section that has an area of 3790 mm? and its moment of inertia about the…

A:

Volumes

Volume usually is the dimensional quantity that involves the evaluation of any three-dimensional figure enfolded inside a closed space. The SI unit (International System of Units) of volume is m3 and the dimensional unit of volume is [L3]. For estimation of the volume of any figure, various formulae are used. Another application of volume includes the reference in the sound levels, the higher the sound intensity, the louder the sound heard, and hence, the larger the volume. The SI unit of sound volume is decibels (dB).