Calculate the synchronizing torque for one mechanical degree of phase displacement in a 6,000-kVA,50-Hz, alternator when running at 1,500 r.p.m with a generated e.m.f. of 10,000 volt. The machinehas a synchronous impedance of 25%.[544 kg.m] (Electrical Engineering-III, Madras Univ. April 1978; Osmania Univ. May 1976)A 10,000-kVA, 6,600-V, 16-pole, 50-Hz, 3-phase alternator has a synchronous reactance of 15%.Calculate the synchronous power per mechanical degree of phase displacement from the full loadposition at power factor 0.8 lagging.[10 MW] (Elect.Machines-I, Gwalior Univ. 1977)

As per the guidelines of bartleyby I need to answer first question only.so kindly repost other…

Calculate the synchronizing torque for one mechanical degree of phase displacement in a 6,000-kVA, 50-Hz, alternator when running at 1,500 r.p.m with a generated e.m.f. of 10,000 volt. The machine has a synchronous impedance of 25%. [544 kg.m] (Electrical Engineering-III, Madras Univ. April 1978; Osmania Univ. May 1976)

Calculate the synchronizing torque for one mechanical degree of phase displacement in a 6,000-kVA, 50-Hz, alternator when running at 1,500 r.p.m with a generated e.m.f. of 10,000 volt. The machine has a synchronous impedance of 25%. [544 kg.m] (Electrical Engineering-III, Madras Univ. April 1978; Osmania Univ. May 1976)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Two 60MVA, alternators operate in parallel. The setting of the governor are such that the rise in speed from full load to no load is 2% in one machine and 3% in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 120MW, what will be the load on the first machine (with 2% speed regulation) when the total load is reduced to 80MW?
A 2MVA, 2.3kV three – phase Y – connected alternator operates at rated kVA at a power factor of 80%. The dc armature winding resistance between terminals is 0.08 ohm. The field takes 70 A at 125 V from an exciter equipment. Friction and windage loss is 20kW, iron losses 36kW and stray load losses are 2.0 kW. Calculate the efficiency of the alternator. Assume the effective armature winding resistance is 120% of the DC resistance. a. 94.0 % b. 92.1 % c. 93.2 % d. 89.5 %
Eo(LL) (V) a) 3000 b) 2500 2000 1500 1000 500 0 No-load excitation curve @3600rpm 0 1 2 3 4 5 6 DC Excitation current (A) 7 The figure above shows the no-load excitation (LL) curve of a 3-ph, 2-pole, 60 Hz, 1000 kVA, 2.3 kV synchronous alternator at rated speed. The alternator has negligible resistance and Synchronous Reactance Xs = 1.2 n/phase. If the alternator is synchronized to the Power Grid at 2.3 kV (Line to Line), calculate the following: 8 9 10 The value of excitation current required for full load current at 0.7 pf lagging (over-excited). |EO(LL)I IF The alternator current and reactive power when it is delivering 80% rated power (0.8 MW) and its DC excitation current is 4 A. IL Q3ph
An alternator has 6 poles. (a) At what speed must the machine be driven to develop 60 cycles? 25 cycles? (b) What frequency is developed if the speed is 1000rpm? Please give the complete solution for this problem. Thank you!
There are 144 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 1500 electrical and the flux per pole is 0.05 Weber sinusoidallly distributed. Calculate the emf induced per phase.
A 3-phase star connected, 1500 kVA, 13 kV alternator has an armature resistance of 0.9 ohm and a synchronous reactance of 8.0 ohms. When carrying rated load voltage, calculate the generated voltage per phase at loads of I.) Unity P.F. ii.) 0.8 lagging P.F. iii.) 0.8 leading P.F. iv.) calculate the voltage regulation for each load and determine best regulation.
b) Explain the conditions of parallel connection of alternators and how these conditions are fulfilled.
An alternator of frequency 50.3 Hz is to be synchronized with an infinite bus of frequency 50 Hz by means of three-dark- lamp method. The lamp-flicker per minute will be
4. A 2 MVA, 2.3kV, three-phase Wye connected alternator operates at rated kVA at a power factor of 80 %. The dc armature winding resistance between terminals is 0.08-ohm. The field takes 70-A at 125-V from the exciter equipment. Friction and windage loss is 20-kW, iron loss 36-kW and stray power loss are 2.0-kW. Calculate the efficiency of the alternator. Assume the effective armature winding resistance is 120% of the dc resistance.
A three-phase, 4-pole, 1,500 rpm alternating having a double layer-windings with 18 turns per coil. The slots per pole per phase are 10 and the coil span is 22 slots. The spread phase is 60 degrees and the flux per pole is 0.0625 Weber. If the armature windings are wye connected. a) Determine the generated voltage per phase and the line to line voltages. b) If the alternator is delivering a three - phase load of 1,200KW at 0.8 lagging power factor what is the line current of the alternator
A 9.9 kV, Y-connected, 3 phase alternator has a synchronous reactance of 8 ohms per phase and negligible resistance. At a certain field current the armature is known to induce 8.2 kV per phase. Calculate the power that can be developed by the alternator at this excitation.
13. A 3-phase, 16 pole alternator has a star connected winding with 144 slots and 10 conductors per slot. The flux/pole is 0.04 wb (sinusoidal) and the speed is 375 rpm. Find the frequency and phase and line e.m.f. The total turns/phase may be assumed to series connected. [50 Hz, 2035 Hz, 3525 V] (Rajiv Gandhi Technical University, Bhopal, 2000)