Use two different bulbs with different rated values in each experiment. To standardize the procedures, label light bulb as follows:- L1 = rated power 0.5W or rated voltage 10V or (10V, 0.5W) L2 = rated power 3W or rated voltage 12V or (12V, 3W) Write these rated values in Table 0 (Col.1 and 2). Calculate the resistance for each L and write it in Table 0 (Col.3). Show your calculations clearly. Table 0: Bulb resistance value (calculated using rated values) 1-Rated power (W) | 2-Rated current (A) or Rated voltage (V) (read from bulb) Bulb Type 3-Bulb resistance R(N) (read from bulb) L1

Use two different bulbs with different rated values in each experiment. To standardize the procedures, label light bulb as follows:- L1 = rated power 0.5W or rated voltage 10V or (10V, 0.5W) L2 = rated power 3W or rated voltage 12V or (12V, 3W) Write these rated values in Table 0 (Col.1 and 2). Calculate the resistance for each L and write it in Table 0 (Col.3). Show your calculations clearly. Table 0: Bulb resistance value (calculated using rated values) 1-Rated power (W) | 2-Rated current (A) or Rated voltage (V) (read from bulb) Bulb Type 3-Bulb resistance R(N) (read from bulb) L1

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 14RQ: 14. A 6-V lead-acid battery has an A-hr rating of 180 A-hr. The battery is to be load-tested. What...

See similar textbooks

Similar questions

Given this circuit: A voltmeter is placed across the resistor 47 ohm and its reading is -2.5V, Determine whether the diode is functioning properly or not.
B/ An 8v zener voltage at 25 C has negative temperature coefficient of 0.05%C, what is * ?the change in zener voltage at 60 C
Question 5 Assume the zener diodes are all ideal in the circuit below and let V1=3.7 V, R1=935 2, R2=1,04702, and R3=855. Determine the output voltage Vo. Express your answer in Volts and round to the 1st digit to the right of the decimal. R1 V1 D1 5V R2 D2 3V {R3 D3 2V Vo
Determine the voltage at resistor R1 if the Zener voltage is 5.1 V.
D3 D1 V1 sine R1 1 kHz D2 D4 Given: • V1 = 5.9 Vrms • R1 = 7 kOhm • Diode voltage = 0.9 V What is the maximum voltage across resistor R1 (in V)?
11 R2 1K R1 D2 1K 5V D1 Determine the voltage across the resistor R2. (assume Zener voltage is 3 volts and Diode forward voltage is 0.7V) *
Procedure 1. Use multisim simulation package to simulate the circuit shown in the figure 5. Consider the following. Transistor type 2N2222A (NPN) and 2N3702 (PNP), Diode type (1N4007G). +20 V R 470 D Vut D2 RL 16 N V, R2 470 2 -20 V Figure 5.Class AB simulation circuit diagram. 3. Discuss the efficiency compared to class A power amplifier. i. he avan i
10 K The diodes in the circuit are Silicon with forward voltage of 0.7 V. Fill up the table showing the state, voltage and current of each of the diodes. ww 8 K D1 Show how you validated the state of each diode. Follow the reference shown in determining whether the diode voltages and currents are positive or negative. 1)1 mA 5 V 1K Diode State VD iD + VD D1 D2 D3
i. Draw a circuit diagram of potentiometer method with naming the components and derived the ratio of the two potentiometer readings. ii. In a measurement of resistance by potentiometer, the voltage drops across resistor under test and across 0.0252 standard resistors were found to be 0.882V and 1.2 V respectively. Determine the value of under test. iii. Write two advantages and disadvantages in Potentiometer method.
3 Determine the labelled voltage and currents if V1 = 10 V and V2 = 5 V. Assume diode cut-in voltage of 0.3 V and internal resistance of 0.1 k Ohm. Write final answer in following format: Vo=xx volt, Id1= yy mA, Id2= zz mA 0.5 ΚΩ V₁0 ww 0.5 ΚΩ V₂0 ww IDI ID2 Enter your answer D₁ KH D₂ KH 19.5 ΚΩ Vo
Give the color bands of the following resistors with 10% tolerance: 1. 1k Ohms2. 220 Ohms3. 1.5 MOhms4. 100 Ohms5. 500 KOhms
When resistors with higher wattage ratings are required, resistors are generally used to dissipate the excessive heat. a) Variable b) Fixed c) Wirewound d) Preset The diode is considered shorted when both anode and cathode has a) Low resistance b) High resistance c) Different resistance d) None of the above When two resistors are connected in parallel then their overall power rating is a) Increased b) Decreased c) Doubled d) Reduced