Calculate the service tensile load capacity for an angle bar L 125 x 75 x 12 A53 steel connected with 13 A490 bolts as shown in the Figure 2. Diameter of holes is 3mm larger than the bolt diameter. Bolt diameter = 13 mm Standard hole = 24 mm Use hole diameter = 13 + 3 = 16 mm a = 43.5 mm b = 51 mm c = 36 mm d = 252 mm

Calculate the service tensile load capacity for an angle bar L 125 x 75 x 12 A53 steel connected with 13 A490 bolts as shown in the Figure 2. Diameter of holes is 3mm larger than the bolt diameter. Bolt diameter = 13 mm Standard hole = 24 mm Use hole diameter = 13 + 3 = 16 mm a = 43.5 mm b = 51 mm c = 36 mm d = 252 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.8.6P

See similar textbooks

Similar questions

A76 x 76 x6 mm angular section shown is welded to an 8 mm thick gusset plate. The length L1 is 65 mm, L2 is 125 mm, and the cross sectional area of the angle is 929 sq.mm. Fy-248MPA and Fu -400MPA. Gusset Plate Alowable Sresse Alowable tensle stress igross ara)0.00 Alowable tereile stres net area)0SOF. Allowable shear stress (net ares)0.30F. Determine the value of P based on net area using a strength reduction coefficient of 85% O 138.24 KN O 140.14 kN O 157.93 kN O 304.00 N Next
Steel design- Base plate I need asap.. Answer this problem complete solution ty.. thank you *use handwritten.
sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts t=12 mm t=12 mm P. P- P 300 75 75 75 Edge distances -75 mm dhole for tensile and rupture d, +3 mm dnole for bearing strength for L- de +1.5 mm Fy 248 MPa F.- 400 MPa
Design the size and length of Fillet weld for the lap joint shown below, Use SMAW E70XX process, plates are A-36 steel? 90k LL 40k DL R-X7 5" Gusset P 8 90k LL 40k DL
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related beams were provided in Chapter 4 as Exercises 4. I through 4.11. These free-body diagrams constitute exercises that will be used here and again in Chapter 12. Follow these instructions carefully to save time later: (a) On each sheet of engineering paper reserved for analysis, calculate the vertical shear specific to that member at appropriate intervals across the length of the free-body diagram. Be sure to solve for locations where shear passes through zero. (b) On cach sheet of engineering paper containing the tree-body diagram, neatly draw the related shear diagram directly below the associated free-body diagram. The shear diagram should be located in the middle one-third of the page. Reserve the bottom one-third of the sheet for the bending moment diagram introduced in Chap- ter 12. Be sure to show…
PROBLEM 9.9 9.10 in the bolted connection of Figure 9.12, assume that the bolts are in. in diameter and that the allowable shear stress for the bolts is 14,500 psi. Based on bolt shear only, compute the safe allowable load P that may be applied. 9.2 Cc
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
The diagonal at the left to the connection is a double angle 90 mm x 90 mm x 8 mm, with area of 2700 mm?, bolted to the 8 mm thick gusset plate. Bolt diameter = 16 mm Bolt hole diameter = 18 mm Bolt bearing capacity, Fp = 480 MPa Bolt shear strength, Fv = 68 MPa Steel plate strength and stresses are as follows: Yield strength, Fy 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 0.60 Fy Allowable tensile stress on the net area = %3D 0.50 Fu Allowable shear stress on the net area = 0.30 Fu Bolt bearing capacity, Fp = 1.2 Fy Calculate the allowable tensile load, P(kN) under the following conditions: %3D
5. Find the allowable strength of the welded connection with a minimum throat size shown below. Base metal: S275 Fy = 275N/mm² Fu = 430N/mm² Weld metal tensile strength: Fe = 480N/mm² [all dimensions are in mm] -10mm thick gusset plate 150 125 125 -10mm thick gusset plate 125 VIEW A-A a 125 -PL 150x12 PL 150x12 -PL 150x12 A
2-D flat plate.
Agui - 4550/2 =2276 two plates each with thickness t = 16 mm are bolted together with 6-22 mndia. bolts forming alap Joint - Bolt spacing are follows St=40mm S2 - 80mm, 53= 100mm effective bolt hole dia is 25mm A36 is used. Compute the allowable tensile strength t = 16 mm ob 27 40 60 80 40 +=16mm S1-40 S2-100 52-40 P 7 @ 4umm