Answered: Calculate the rms value of A.C. as…

Engineering

Electrical Engineering

Calculate the rms value of A.C. as shown in the figure. 13 2A- -2A 12

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter7: Alternating Current, Power Distribution, And Voltage Systems

Section: Chapter Questions

Problem 16RQ

See similar textbooks

Related questions

Q: Two equal voltages are out of phase with respect to each other by 90 elec deg. If their sum is 311…

Q: For the circuit shown below, determine the real, reactive and apparent power for each element…

A: Write KVL equation for the circuit given and solve for current I; 2402∠60°-I5+8j-2802∠30°=0…

Q: Define Power Factor in five ways with respect to each of the following: >angle between the voltage…

A: The cosine of angle between voltage (V) & current (I) is termed as power factor.

Q: Complete the sentence The power factor must be close to will be reduced To insure that losses in the…

A: Power factor is the ratio of Real power(kW) to apparent power(kVA). It can also be defined as the…

Q: A residential four-wire system supplies power at220 V rms to the following single-phase…

A: (b) For first phase total load are – Since loads are bulb so that total power is real and reactive…

Q: What is the correct notation for a load factor? a) Ω b) ∞ c) ∑ d) ⅄

Q: 8.1 The load duration curve for a power station is as shown in the below figure. The reserve…

A: we need to determine reserve capacity.

Q: Find the total average power absorbed and the total average power supplied in the network from the…

A: Fig: Given circuit calculate z1…

Q: QUESTION 11 A resistor, inductor, and capacitor are connected in parallel with a function generator.…

A: The solution is given below

Q: (a) Explain the generation of single phase alternating voltage. Illustrate with a diagram.

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Ix ZL 220° A rms 2 Ix

A: In this question, Determine the maximum power transfer to the load impedance ZL For maximum power…

Q: Complete the blank The load of 660 kVA with 0.62 power factor lagging, then the kW rating of the…

A: Load rating 409.2 KW

Q: ば 52+GS+13

A: In the question Find the Inverse laplace transform of the given function. We know cos(at)…

Q: (i) Plot the load profile of the residential house. (ii) Determine the load factor. (iii) Determine…

A: The formula to calculate the load factor of a power unit is load factor=PavgPmax Here, Pmax is the…

Q: A step down chopper has Vs = 230 V and R = 10 N. For a duty cycle of 0.4, the power taken by the…

A: A step down chopper has Input voltage, Vs = 230 V Resistor, R = 10 Ω Duty cycle, α = 0.4 The power…

Q: HIGH VOLTAGE (Can you explain in detail? Thank you) Describe briefly, with the aid of suitable…

Q: (a) An electrodynamic wattmeter is used to measure the electrical power in a circuit. The diagram in…

Q: Problem 223: EE Board March 1998 A load of 20 + j35 ohms is connected across a 220 volts source.…

Q: Findd the 2) and RMS valne 24 10 tG)

Q: Compute the rms value of the voltage waveform shown v(1) (V) ? 4 6 8 t(s)

A: The signal is defined from time t=0 to t=4 sec. The definition of signal is as follows: v(t)=2t…

Q: Volts 12 t (sec) Find the RMS value of the voltage waveform, Find the average power if 8 2 resistor,…

Q: The inductive reactance in series with Z in the circuit shown below has a value of 25 ohms. If the…

A: In this question, What is reactive part of Z in shown the figure. Power P= I2 R

Q: 15

Q: Image 1: What is the complex power delivered to the load? Image 2: What is the average power…

Q: Write down the Construction of an alternator with the help of diagram and write its Principle of…

A: Alternator is derived from ' alternating ' . Alternator is an electric generator which converts…

Q: I, -j3 k2 j1 k. 500 2 ell 201, 4 k2 Ix 10 k2 0.2/0° V rms (t

Q: c) ead /y 1. Peak to peak ripple is defined as a) The difference between average de voltage and peak…

A: 1. Peak to Peak ripple is defined as The difference between maximum ac and average dc voltages. So…

Q: Vs 18 V pk RL 220 N (a)

Q: The feeder is a conductor connecting the sub-station (or localized generating station) to the area…

A: c. True The feeder is a conductor which is for connecting the substation (or a localized generating…

Q: Write down the Construction of an alternator with the help of diagram and write its Principle of…

Q: c) Describe the following terms as they relate to utility providers; i) Peak Plant ii) Baseload…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: kind of power that exists in an AC circuit when the current and voltage are not in phase. * A.…

A: We need to select option for given statement .

Q: 3. When an electrician refers to a voltage as being 1200 V ac, it is understood that he means the…

Q: the currents 11

Q: 13/ choose the correct answer The variation of the load is considered over a period of one year…

Q: hort term and long term effects of wind energy on power system

A: SHORT TERM AND LONG TERM EFFECTS OF WIND ENERGY ON POWER SYSTEM: 1. The following factors are…

Q: (d) The impedance in ohm of each coil. (Polar form) (e) The value of the resistance in ohm of each…

Q: Low power factor has some adverse impact on both the transmission line and on the consumer…

A: “Low power factor has some adverse impact on both the transmission line and on the consumer…

Q: Compute the rms value of the voltage waveform show v(t) (V) 4 4 2 4 6 8 t (s)

A: In this question We need to determine the rms value of the given waveform. We know rms value of…

Q: That is the RMS value of an AC voltage that has a 347 V peak? Pa. 245.3 Ob.490.6 Oc. 265.7 Od.469.3…

A: The relationship between rms and peak value is given by: V(rms) = V(peak)÷√2 Simliraly ,V(peak) =…

Q: Given the test circuit below, the wattmeter reads: 2400 watts, the ammeter reads: 14.0 ARMS, and the…

A: In this question, Reading of the voltmeter, ammeter and Wattmeter given Find the value of the…

Q: Determine the power and the rms value of: (a) 8(t) = C cos (wot +0) (b) 8(t) = Cı cos (@it +61) + C2…

A: Power and rms value of given Sinusodial waveform Acos(wt) RMS value = A/√2 Power P= A2 /2

Q: What is the value of real power supplied by the source in the figure? 60 ww 30/0° V rms -j20 42

A: Equivalent impedance can be obtained by,…

Q: Two equal voltages are out of phase with respect to each other by 90 electrical degrees. If the…

Q: 3. The equations of currents in parallel - connected devices are: i₁ = 11.3 sin (wt +) 8.5 cos (wt +…

Q: A load of 23 kVA, with .65 power factor lagging is connected to a 240 volts line. How much…

A: Given data, S1=23 kVAcosϕ1=0.65 laggingVL=240 Vcosϕ2=0.95 lagging

Q: 4.) A load of 23 kVA, with .65 power factor lagging is connected to a 240 volts line. How much…

Q: current of 10 A rms results when a single-phase circuit is placed across a 220 V rms source. The…

A: Given that, Source voltage, Vrms = 220 V RMS current, Irms = 10 A Current lags the voltage by 60°

Q: Generate a conclusion on this following statements: Determine and analyze the voltage regulation…

A: GIVEN: resistive load inductive load capacitive load DETERMINE: the…

Q: Assume you are working on sinusoidal ac supply voltage which is in the form of 150 sin 220 t. So…

A: In AC sinusoidal voltage wave, the expression of Root Mean Square value of voltage (VRMS) is given…

Concept explainers

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.

Question

Calculate the rms value of A.C. as shown in the figure.
13
2A
-2A-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

DC/AC MOTOR (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.) A current of (120-j150) A flows through a circuit when applied voltage is (8 + j12) V. A. What is the magnitude of the circuit impedance: a. 0.0635 ohm b. 0.0256 ohm c. 1.52 ohm d. 1.325 ohm B. What is the reactive power? a. 825.75 VAR b. 525.68 VAR c. 639.75 VAR d. 438.72 VAR
PLEASE RESOLVE! THE FINAL ANSWER MUST BE IN THE CHOICES. DC/AC MOTOR (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATIONS NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.) A current of (120-j150) A flows through a circuit when applied voltage is (8 + j12) V. A. What is the magnitude of the circuit impedance: a. 0.0635 ohm b. 0.0256 ohm c. 1.52 ohm d. 1.325 ohm B. What is the reactive power? a. 825.75 VAR b. 525.68 VAR c. 639.75 VAR d. 438.72 VAR
3. The secondary voltage can rise above its rated value when the load is a. resistive. b. capacitive. C. inductive. d. an RL series combination.
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
Solve for B to E: Answers: a. 2247.8405 Ab. 292.0629 kVc. 2291.3829 Ad. 667.10875 MW, 53.2164 MVAR (cap), 669.228 MVAe. 32.89125 MW
Draw rough sketches showing the following:a. A current which lags the voltage by 60 degreesb. A current which leads the voltage by 60 degreesc. A current which lags the voltage by 180 degrees
Determine the rms current I as shown in figure 2. Source voltage is already in RMS value(Answer must be in polar formand should be in 4 decimal places).
Consider the switching waveforms shown below, operating with a duty-cycle of 30%. Which statements correctly describe the switching circuit, load and circuit operation? (Multiple answers possible, but wrong answers will deduct marks) Voltage across load Voltage (V) 000 120 0000 100 80 60 40 20 30 Time (us) The load must be predominantly resistive. The average current in the load is 1.0A. The RMS current in the load is approximately 1.414A. The load must be predominantly inductive. The resistive part of the load is 200ohms. The average current in the load is 0.6A. O The resistive part of the load is 50ohms. 0 0 10 20 40 50 60 Current (A) 2 5 0.5 0 0 10 Current through load 20 W 30 Time (us) 40 50 60
In a load test on transformer the no load voltage is 240V. The terminal voltage drop is 225V on resistive load condition. The primary voltage of transformer is 350V. The primary and secondary currents are 0.45A and 0.671A. What is the efficiency of the transformer? O a. 68% O b. 95.85% O c. 64% O d. 43.19%
Calculate the RMS current through R2 in the diagram IR1 = 6.06mA peak, R2 = 2.7 kohms, total current is 9.522mA RMS 3.25mA RMS 5.24mA RMS 7.41mA RMS 9.0mA RMS
Set the amplitude, phase, and frequency parameters of the AC voltage source block according to the values shown in the figure below
What is power loss