Beam ABC is under two distributed loads. Point A is a Pin, while Point C is supported by a roller. Find the Reactions at A and C. A reaction C reaction = (A) 0 i+ B 1 2 i+ 2.0 X10² N/m jN IN 1.5 X10² N/m 1.0 X10² N/m 3 4 5 6 7

Q: On the drawing (attached , apply a datum feature symbols to create a datum axis A-B by using the…

A: The given data is: For left side: Shaft Diameter Upper Limit=9 6.40 mmShaft Diameter Lower Limit=ϕ…

Q: Jse commands (rectangle, mirror) and List he commands to draw the following drawing start from a…

A:

Q: The following is the bearing and length measurements of an opentraverse A) Determine the latitude…

A: The latitude of the traverse line is extend on the north and south direction and departure of the…

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: Determine Ix and Tx.

A: GIVEN- A PLANE FIGURE TO FIND- MOMENT OF INERTIA ABOUT X-AXIS AND CENTROIDAL AXIS.

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: What does on the lines, 4 & 3 indicate

A: Line 3 in View 2 represents the level at which the plan or top view (View 1) is drawn. Although the…

Q: Find the centroid, ^y, and moment of inertia Ixx of the following sections.

A: The moment of inertia about X-Xaxis can be found using parallel axis theorem, IXX=IGG+A×h2IGG=MOI…

Q: Given the multiview projection of the solid, draw its isometric view.

A: Solution- The given diagram is shown below. To Determine,  The isometric view

Q: 6. Draw a true distance between a point Q and a plane B. Vs he 7. Draw a piercing point and…

A:

Q: y 200 mm 300 mm → 125 mm 125 mm 60 mm 150 mm

A:

Q: at state of given (All in The Stres point is MPa) 80 100 100 i) And Principal Stren & Principal…

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: Determine how far is the centroid of the given cross section above the base. 6-504 2-50" 9.0" 6.5"…

A:

Q: Arc command and its abbreviation is A character is the only command can be used to draw an arc in…

A: It is required to state whether true or false statement.

Q: 4 in 2 in 4 in 8 in -12 in- -16 in-

A:

Q: top wiew Units are in millimeter right side 40 IS 35 ーネィー ー子ィー front viw 1-..

A: Given orthographic views- Top view Front view Right side view

Q: Q1: determaine the coordinates of the centeroid of the shaded area 20 40 50 20 40 30 140

A: The polar coordinate system is a method to calculate points in the system location by proper…

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: 80 mm -L- В D 60 mm

A:

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: show the (c)

A:

Q: weétermine the yalue j = 2. Det ermine the Yalue & I with Respecd to centroidal X axis =

A: 1. Value of y¯ Let 1 & 2 be the rectangle and 3 & 4 be the triangle.y¯=∑ay∑a…

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: What are the commonly available switch actions?

A: Commonly available switch actions? ON-OFF, SPST. SPST = Single Pole, Single Throw.  (ON)-OFF,…

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: Y

A:

Q: Links CF connects members AD and EG. The two vertical links having a rectangular cross-section…

A:

Q: Explain why wx = 2/3(9-x)

A: Given:Required:To explain loading intensity for 6<x<9