Calculate the output C (s) of the system whose block diagram is given below. D(S) R(s) + C(s) GO G1 G2 G3 H1 H2 Sekil-2

Q: Question 1 Base on Statcom a)Draw the block diagram of the STATCOM b) Give the operating mode of…

A: Types of FACTS devices based on connection Series TCSR SSSC TCSC TSSC Shunt  STATCOM SVC…

Q: frequency modulation and what is the highest value for

A:

Q: Please explain step by step (like the charging and discharging) how the output of this uncompensated…

A: The above circuit consists of a lead compensator made of resistors and capacitors. To this, a square…

Q: What characteristics are used by mode 2 in the 8255?

A: We will refer the concept of microprocessor 8255

Q: Q-1-a) From the circuit in the Figure-1, determine the DC-bias operation Parameters: (i) IB (ii) Ic…

A: Given:

Q: State the advantages and disadvantages of the block diagram reductio technique.

A: Block diagram reduction techniques are used to find transfer function in control system. Transfer…

Q: H3. (Dynamical System ) Explain various types of oscillator in non linear system

A: Nonlinear oscillator : Whenever a force is exerted on any particle then there is movement in the…

Q: Clipper circuit: Vi (p-p)= 10 volt (Sinewave) F=1 kHz R= 10 Kohm V= 4 volt Find and Sketch the…

A:

Q: 1) The trigger waveform of the monostable multivibrator has an amplitude that Vcc must be less than…

A: The Types of Multivibrator used in the digital electronics systems are enlisted as follows :…

Q: Draw What is the cross over distortion in class B?

A:

Q: How does R-2R DAC is better than Binary-weighted Resistor DAC?

A: Given that  How does R-2R DAC is better than Binary-weighted Resistor DAC?

Q: Find the output voltage of an R/2R ladder DAC for a binary code (11001101). Assume Rf = 2R and ON…

A:

Q: 1) Given Vcc=12V, voltage input at Pin 6 is 9V, voltage input at Pin 2 is 5V, decide the output…

A: In this case, the following circuit diagram is given:

Q: (2) Consider a frequency modulated signal. The modulating signal frequency is increased from 10 kHz…

A: In this question we have to find the correct optionsrgarding modulated signal bandwidth

Q: Construct an Multiplexer 8*1 with two Multiplexer 4*1 and additional gate

A:

Q: 15.Calculate the DAC output of 010000 by R-2R ladder network method, and circuit analysis. Assume…

A: In this question,  We need to determine the DAC output of 010000 by R-2R ladder network method.…

Q: This type of circuit might be used in A B En Address buffers Data buffers The timing circuit O The…

A: Ans :- Data buffers  This type of circuit is used in data data buffer.

Q: The offset voltage describes the dc component of a dc electrical .signal

A: according to the question we want to know what offset voltage describes

Q: What are Test comparators?

A: We have been asked about Test comparators.

Q: Nyquist criterion margins

A: To explain: Nyquist criterion margins.

Q: (B) For the mechanical system in figure (4). Drive the transfer function Y(s)/F(s) KI M K2 Figure…

A: we need to find out transfer function for the given mechanical system.

Q: Impedance inversion can be achieve using

A:

Q: In common source configuration the input resistance of a JFET will be approximately____. a.500 Ohm…

A:

Q: For a DC-DC Converter; The input voltage of the circuit is 12 V, the switching frequency is 1 KHz,…

A: A DC-DC converter has, Input voltage (Vin)= 12 volts Output voltage (Vo)= 48 volts Output Power…

Q: n ideal operational amplifier circuit in the closed-loop negative-feedback configuration is shown in…

A:

Q: 2. Sweep Vin (0 to 1V) and plot Id. Vth = 0.4V. Indicate the region of operation clearly. 1V Vin HE…

A: Given that , Vth= threshold voltage=0.4v VD= drain voltage=0.5v Vs= source voltage=1v Id= source to…

Q: 3. Draw the schematic diagram of the series-positive limiter and the series-negative limiter;…

A: It is an electronic device that consists of two terminals (Anode and Cathode).It is a unidirectional…

Q: Please validate the saturation assumption

A:

Q: Q-1-a) From the circuit in the Figure-1, determine the DC-bias operation Parameters: (i) IB (ii) Ic…

A: As per our policy, i have attempted 3 parts . Given  β=100RB=380 KΩRC=1 KΩVBB=VCC=12 V Calculating…

Q: Offset voltage compensating network is connected in between pin of LM741 op-amp number ....... &...…

A: LM741 is an 8-pin operational amplifier. A LM741 op-amp is shown below,

Q: 5. The smallest amplitude pulse that can be generated by the stimulator is 100 mV. Describe how you…

A:

Q: Solve all questions, please.

A: In this answer let us try to answer the given questions as shown below.

Q: Clamper circuit: Vi (p-p)= 10 volt (Sinewave) F=1 kHz R= 10 Kohm V= 4 volt C= 1 micro F Find and…

A:

Q: The most commonly used demodulation technique for FSK uses circuit.

A: According to the question we have to discuss about the most commonly used demodulation technique for…

Q: Why do we need three RC network for phase shift oscillator? Can it be two or four ? and why

A: In this question we will write phase shift oscillator...

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.