Calculate the dynamic viscosity of oil, which is used for lubrication b/w a square of size 0.8 x 0.8 m2 and an inclined plane with angle of inclination30, wt = 300 N, slides down the inclined plane with a uniform velocity of 0.3 m/s. the thickness of oil film is 1.5 mm.

Calculate the dynamic viscosity of oil, which is used for lubrication b/w a square of size 0.8 x 0.8 m2 and an inclined plane with angle of inclination30, wt = 300 N, slides down the inclined plane with a uniform velocity of 0.3 m/s. the thickness of oil film is 1.5 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 6.8 m long, f...

A: Given, The Given section : W12×79 properties of the given Section are as follows: A = 14,500 mm^2 ...

Q: A 1:75 model of a boat has a wave resistance of 0.02 N when operating in water at 1.0 m/s. Find the ...

A: Fm=0.02N Vm=1m/s

Q: (a) What is the irmportance of a job lay-out ? Sketch a typicai job layout for R.C.C. framed 9. buil...

Q: Please show complete solutions. Considering EI is constant and the value of P is 425kN, calc...

Q: For the beam shown, find for the moment area the strain at D and the rotation at A, using the moment...

Q: A constant head permeability test is performed on soil that is 4 cm2, and 2.5cm long. The head diffe...

Q: he following information belongs to a target cost contract: Target cost = $250 M Target band = $230 ...

A: The information for a target cost contract is given below, Target cost = $250 M Target band = $230 M...

Q: 50 mm wide, 500 mm deep is reinforced at the bottom with 4-2e-mm-diameter bars and at the top with 2...

A: According to given data A rectangular beam 250 mm wide, 500 mm deep reinforced at the bottom with 4...

Q: Determine the tensile steel strain

Q: FUNDAMENTALS OF GEOTECHNICAL ANALYSIS During a Standard Penetration Test on silty clay soil, blow...

A: In a Standard Penetration Test on silty clay soil,The number of blows are as follows,1. For first in...

Q: Figure shown below, a simply supported beam and the cross-section at midspan. The beam supports a un...

Q: CONSTANT HEAD PERMEABILITY TEST a. why the need to get the temperature of the collected water? b. wh...

A: Concept Constant head permeability test Permeability also known as hydraulic conductivity is measure...

Q: Example 5.23 Two 30 cm wells completely penetrate an artesian aquifer of thickness 15 m and are spac...

Q: A 3m Water 45° C 3m B. In the figure shown, the gate in the shape of an arc of a circle of radius 3m...

Q: An A36 angle bar is used as a tension member connected on both legs with 17 mm . Given that s = 49 ...

A: When a material is stressed, it deforms in a way that can be recovered. A material's yield strength ...

Q: A symmetric I-shaped built up steel beam is composed of 180 mm x 9 mm flange plates at top and botto...

Q: The axially loaded column given in the following image is a W14x53 with L = 8.2 m: 2 m 2 m Strong ax...

Q: The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm. Usi...

A: This question belongs to subject reinforced concrete cement. In this question find out amount of ten...

Q: Question 45 Calculate the nominal shear strength (kN) of 4-legged stirrups 10-mm-diameter, spaced at...

A: This question is related to the Design concrete structure. In this question we calculate nominal she...

Q: A Lecture room with an area of 50 square meters( 5m at the shortest side) accommodates 45 students. ...

A: Given, Area = 2.5m x 5m Coefficient of utilization (UF) = 0.35 Maintenance factor (MF) = 0.80 Lumen...

Q: A built up l-section is formed from plates welded together as shown in the figure. It is to be used ...

A: Given data: L=3.5m E=200Gpa To find Fcr?

Q: A cylindrical log (2m in diameter, 1.2m high, and| weighing 10.5 kN) floats in water. Its center of ...

Q: iven the same vertical alignment connecting a -4% grade with a +2% grade vith the PVC station at 34+...

Q: Question 27 1 points Save Ans A built up l-section is formed from plates welded together as shown in...

Q: What is the difference in meaning between the following verbs? Moke them in sentences: Evaluate - As...

A: Evaluate - Asses Evaluate is defined as the methods and measures which is used to judge the student...

Q: Given a vertical alignment connecting a -4% grade with a +2% grade with the PVC station at 34+64 wit...

Q: A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The bea...

Q: According to the provisions of NSCP 2015, in flexural reinforced concrete members a compression cont...

Q: The kinetic energy of a 4.0 kg object moving at 3.0 m/s is: 1. 12 J *2. 18 J 3. 36 J 4. 48 J

Q: n loads are service conditions: 95 kN 21 kN MPa 5 MPa te cover to the centroid of steel reinforcemen...

A: According to given data A square footing 2.3 m x 0.32 m thick supports a 300 mm square column at it...

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars a...

A: Given, Width of beam=250 mm Depth of beam=500 mm Bottom bars =4-20 mm diameter Top bars=2-16 mm diam...

Q: A prismatic bar is fastened between two rigid walls A and B and subjected to loads as shown in figur...

Q: If the depth of penetration for a 2-x-2-x-2-cm cube is 0.5 cm, what is the percent penetration? (Rep...

Q: Calculate the allowable axial capacity in kN if Fy = 345 MPa. Write your answer rounded to the neare...

A: Given, W14 x 53 L = 8.2 m or 8200 mm Fy = 345 MPa

Q: note that you can assume a unit thickness coming out of the page. A 500 m long levee made of compact...

Q: 1. OMITTED given rection of one side are unknown. departures of the given sides and determine the le...

Q: A square footing 2.3 m x 0.35 m thick supports a 300 mm square column at its center. Column loads ar...

A: Given data: DL = 344 kN LL = 251 kN f’c = 21 MPa fy = 415 MPa

Q: What is the Order of the equation? What is the DEGREE of the equation?

A: ORDER AND DEGREE OF THE DIFFERENTIAL EQUATIONS:

Q: estion 9 60mm, 60mm 1 100mm 100mm 100mm 100mm A staggered bolted connection has bolts arranged as sh...

A: The given figure is shown below:

Q: A Lecture room with an area of 50 square meters( 5m at the shortest side) accommodates 45 students. ...

Q: The material of a rubber balloon has a Poisson's ratio of 0.5. If uniform pressure is applied to blo...

A: Given data, The material of a rubber balloon has a Poisson’s ratio of 0.5. If uniform pressure is ap...

Q: Compute for the reaction A and B. Also, WHAT IS THE MAXIMUM NEGATIVE MOMENT. Draw the MOMENT DIAGRAM...

A: Given data in question Overhanging beam Dimensions UDL Point load To find out Reactions SFD BMD

Q: FUNDAMENTALS OF GEOTECHNICAL ANALYSIS A constant head permeability test is performed on soil that i...

Q: A square footing 2.2 m x 0.31 m thick supports a 300 mm square column at its center. Column loads ar...

A: Given, DL = 331 kN LL = 251 kN f’c = 21 MPa fy = 415 MPa Square footing : 2.2×2.2× 0.31M Column: 0....

Q: A W8x40, A36 steel is used as a simply supported beam uniformly loaded over a span of 6.4 m. If the ...

Q: An axially loaded tied column must sustain the following service loads: Total Dead Load = 1,000 ...

Q: Value of effective stress at point C

A: Given data : Dry unit weight γ=16 KN/m3 Saturated unit weight γSat=20 KN/m3 Unit weight of water γW=...

Q: Situation 4] Two tangents that intersect at an angle of 48°40' are to be connected by a compound cur...

A: Given data- Intersection angle D=48o40'Angles of compound curves D1=4.1o & D2=5.5o T1=110 m

Q: beam of rectangular cross-section is subjected to a vertical snear force V. The ear force carried by...

A: Shear force for 1/3rd portion-

Q: A spar buoy is a buoyant rod weighted to float and protrude vertically. Suppose that the buoy is mad...

A: To find the angle (theata)-

Question

Calculate the dynamic viscosity of oil,
which is used for lubrication b/w a square
of size 0.8 x 0.8 m? and an inclined plane
with angle of inclination30', wt = 300 N,
slides down the inclined plane with a
uniform velocity of 0.3 m/s. the thickness
of oil film is 1.5 mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the dynamic viscosity of an oil, used for lubrication between a shaft and sleeve. The shaft is of diameter 0.4m, rotates at 190 rpm and requires a shear force of 2N. The sleeve length of 90mm. The thickness of the oil film is 1.5mm.
A 0.6 m square glass plate slides on a plane with a slope of 30° from the horizontal (Figure 1.2). Knowing that the plate weighs 30 N and that it acquires a constant speed of 5 cm/s, it is asked: determine the dynamic viscosity of the film 0.1 mm lubricant, which is between the plates. Assume the velocity diagram linear in the fluid film). (R: 0.0833 Ns/m2) 5cm/s Figure 1.2 0.1 mm
Determine the surface area and volume of the solid formed by revolving the shaded area 360°about the z axis.
A capıllary glass tube of 0.1 mm internal diameter is immersed vertically in a beaker full of waten Assuming the tube to be perfectly clean and wet, determine the height of the capillary rise of water in the tube when the room tamp is 20°C. Given at 20°C unit weight of water = 0.9980 gm/cc and surface tension 72.8 dyne/cm. %3D
1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/'s, detemine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe. 2. [Ch4 - 2] The kinematic viscosity of a hydraulic oil is 0.0001 m/s. If it is flowing in a 20-mm- diameter commercial steel pipe, find the friction factor for: a. The velocity of 5 m/s b. The velocity of 50 m/s
please
Calculate the followingi. Liquid limitii. Plastic limitiii. Plasticity index
Real liquid (y = 10 kN/m³) is flowing laminar in a pipe at a steady rate, but the direction of flow is unknown. Is the liquid moving upward or moving downward in the pipe? If the pipe diameter is 8 mm Elevation = 10 m - --p = 110 kPa and the liquid viscosity is 3.0 x 10-3 N. s/m2 what is the magnitude of the mean velocity in the pipe Elevation =0 m - --p= 200 kPa
ISU ISTINYE UNIVERSITY I STA N B UL dn 30-cm×20-cm block weighing 150 N is to be moved at a constant velocity of 0.8 nled n inclined surface. If a 0 4-mm-thick oil £GIM with a viscosity of 0.012 Pa.s is he blosoetween the block and inclined surface determine the force required for moving Question 1: the block upward. V=0.8 m/s 50cm 30 cm 200 150 N estion 2:
A rigid container is partly filled with a liquid at 1520 kPa. The volume of the liquidis 1.232 liters. At a pressure of 3039 kPa, the volume of the rigid container is 1.231liters.a. Compute the average bulk modulus of elasticity of the liquid.b. Compute the coefficient of compressibility.c. If the liquid has a density of 1600kg/m3, what is the speed of sound in the medium?
Oil flows through a circular pipe at a rate of 0.4m^3/s. Density p= 960kg/m3 Length of Pipe = 120m Head loss along the length = 7m Roughness of the pipe, ks = 0.07mm Kinematic viscosity v= 2 x 10^(-5) m2/s Find the diameter of the pipe to 3dp. (The final solution should be 0.34m, but i am confused with the method so if you could put a few notes next to calculations that would be very helpful). Ive attached a copy of the moody diagram aswell as it is relevant.
A concrete cube 260 mm on each is to be held in equilibrium under water by attaching a Lightweight foam buoy to it, as shown. (In theory, the attached foam buoy and concrete cube, when placed under water, will neither rise nor sink.) If the specific weight of the concrete and foam are 23.875 kNm3 and 0.55 N/m3, respectively, what is the minimum required volume of the foam. Neglect the weight of the wire.