n=1 Calculate the design moment strength of section shown in Fig(2),and check the ACI Code requirements. Given f'e = 24 MPa and fy=370 MPa.h= 500 + 10 × (n)b=295 + 5 x (n)Where: (n) is Student numberFig. 2hAs 325As 628b6590

Answered: Image /qna-images/answer/95d67684-d884-4313-9a34-78235f19cb4e.jpg

Calculate the design moment strength of section shown in Fig(2), and check the ACI Code requirements. Given f'c = 24 MPa and fy=370 MPa. h-500 + 10 × (n) b-295 +5 x (n) Where: (n) is Student number Fig. 2 h As 6628 b

Calculate the design moment strength of section shown in Fig(2), and check the ACI Code requirements. Given f'c = 24 MPa and fy=370 MPa. h-500 + 10 × (n) b-295 +5 x (n) Where: (n) is Student number Fig. 2 h As 6628 b

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter12: Electric Current And Related Variables In Engineering

Section12.2: Electrical Circuits And Components

Problem 6BYG

See similar textbooks

Related questions

Q: The main reinforcement in RC slab consists of 10 mm diameter bars at 100 mm c/c spacing. When 10 mm…

A: Given data- dia d=10 mm, 100 mm c/c spacing, 12 mm bars. To Find- The new spacing.

Q: A cyclone has a dpc of 5 µm, what is the overall removal efficiency for air stream that has the…

A: Given, particle cut diameter,dpc=5 μmParticle size % mass in that size range 3µm 10.0% 5 µm 20.0%…

Q: Using double integration method determine the value of end shears, end moments and mid-span…

Q: W₁ 1.1m + 1.3m + W₂ 1.1m

A: Given W1 and W2 acts for 1.1 m Note According to the company guidelines i am able to answer…

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall…

A: Since the only question is to find the maximum moment We will draw shear and bending moment diagram…

Q: 1. A theodolite is set up at one end of a level line 150.0 m long. The line is marked by stakes at…

A: As multiple questions are asked and as per the guidelines, first question will be…

Q: #4 Draw the shear and moment diagrams for the beam. A W kN/m 8 m B. 3 m P KN 150 kN.m W= 29 kN/m P=…

A: GIVEN: Beam is shown TO DETERMINE: Shear force and Bending Moment diagram.

Q: Calculate the depth of the neutral axis of the section in PART A in mm

A: Given- The cross section of beam carrying different loading system. Part A…

Q: Situation 6: Combined the two forces P and T, which act on the fixed structure at B, into single…

A: Using simple geometrical constructions and trigonometry, calculate the angle between the forces P…

Q: 42.56 Not found in the list 20 kN/m W 60 kN/m 306.54 309.51 287.94 332.79 10 kN/m 2.0m Not in the…

Q: Solve for the reactions and draw the shear and moment diagram. 116KN

A: PLEASE POST OTHER QUESTIONS IN DIFFERENT QUESTION

Q: Determine the slope correction for steep slope and the horizontal distance AB if two lines AC and…

Q: Find the hearing and sketch the graph of the traverse. scale used

A: Here first we draw the traverse to check the error. Here we see E is not meeting at A…

Q: A cylindrical specimen of dry sand with a minimum and maximum void ratio (emin and emax) of 0.5 and…

A: We have relationRelative density isRd=emax-eemax-emin

Q: A) The following traffic counts were taken on a rural highway during the morning peak hour at…

A: As multilple questions are asked and as per the guidelines very first question will be…

Q: Typical heating values of natural gas from various parts of the U.S. are shown in the accompanying…

A: To find:- the average, variance, and standard deviation

Q: If the resultant force acting on the eyebolt is 520N and its direction is 30° clockwise from the…

A: We know that Magnitude of resultant of a coplanar and concurrent force system is given by R =…

Q: e following data p ial DO = 10 mg al DO = 2 mg/L ution to 1%

Q: lok lok 10 7' 6' 7'A

Q: VA b VB MB

Q: 0.7m 530N/m H 1.3m 0.7m

Q: Mmax=

A: given a cantilever beam with a load of 20k at its free end and Assuming flexure stiffness of the…

Q: The 5-day BOD of a wastewater sample is obtained as 190 mg/L (with k = 0.01 h-¹). The ultimate…

A: Given data- 5 Day BOD- Lt=190 mg/L,decay constant-k=0.01 h-1=0.01×24 day-1.⇒kD=0.434k.time t= 5…

Q: A line was recorded as 2350.00 meters long. The standard tape weighs 0.65 kg, 30.00m long at 20°C…

A: Given:E=200 GPaA=2.50 mm2Gradient=3%Coefficient of linear expansionα=0.0000116 m/°CStandard tape…

Q: A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular…

A: Given, P=330 lb

Q: Draw the shear and moment diagrams for the given beams. Show complete solution by writing the shear…

Q: SS Soil Mechanics And Foundation Engineering The width of a square footing and the diameter of a…

A: Given- Depth of footing Df=0 since footing is on the surface. Width of square footing = Diameter of…

Q: 2. dddd 20 ft 3 KLF Mmax= Ama max= (26100) thote 30 (sixam

Q: Determine the vertical reaction at B for the beam shown. 66.75 KN 53.4 kN 106.8 kN O a. By 160 kN ↑…

A: Given data Find vertical reaction at B (By)

Q: The Froude number of flow in a rectangular channel is 0.8. If the depth of flow is 1.5 m, the…

A: given- Rectangular channel- Froude no. F=0.8, depth of flow y=1.5 m,

Q: The reduction coefficient of a RC column with 4800 mm effective length and size 250 mm : 300 mm is…

A: given- RC column, effective length d=4800 mm, size- 250×300 mm,

Q: Ge: A-16°38, R-1000 ft, PL Sta@+ 26.57 Find: PC and PT stations, length of chord (C), middle…

Q: For Problem 19.6 (assuming normal distribution), determine the probability that it will take a…

A: To find:- plot the data and calculate mean and standard deviation.

Q: 18000 N 1.2m 12000 N/m 0.75m -1.2m

A: Solution:

Q: 16. The neutral axis of a beam is: a) The longitudinal axis along which there is either tension or…

Q: год I KLF Мmax = Am max=

Q: W₁ 1.1m + 1.3m + W₂ 1.1m

A: Given E= 15 Gpa

Q: The areas within the contour lines at the side of a reservon and the face of the proposed dam are as…

Q: Using Double Integration Method derive an expression for the following: a) Reaction at propped…

Q: Imagine that you and four of your classmates have measured the viscosity of engine oil and recorded…

A: To find:- The average, variance, and standard deviation for the measured viscosity of oil.

Q: Traffic on a highway is said to follow the Greenshields model with jam density of 196 pc/mi/ln. The…

Q: Solve for the reactions and draw the shear and moment diagram. 9.35KN/m 2.00 5.00 116KN 9.35KN/m…

Q: من الله 유 | 3klf 20 ft Mmax=

Q: Calculate the pressure drop for the cyclone of Problem 4,2, assuming K =14,

A: Given: D = 0.5 m H = 0.5D = 0.25 m W = 0.25D = 0.125 mm De = 0.5D = 0.25 m ρg = 0.9 kg/m3 V1 = 25…

Q: Define civil piles

A: Foundation:- A building's foundation is the lowest part of the structure that disperses its gravity…

Q: Part A Determine the smallest radius r of each spherical balloon that is needed to lift the boat.…

A: Given : To find : rmin and m ?

Q: homogeneous disk of mass m= 9 kg rotates at the constant rate w₁ = 12 rad/s with respect to nstant…

A: given:mass of disk m=9kgangular velocity ω=12 rad/sabout y axis angular velocity ω2=4 rad/s

Q: A concrete overhang beam with the section shown is to support a 150 mm thick concrete slab with a…

A: "Since you have asked multiple question we will solve first for you. If you want any specific…

Q: 6. An open top box is made by cutting equal squares of side x out of the corners of a piece of…

Q: 2 m 5 m 2 m Silt Clay 3 m A Sand under artesian pressure Bedrock 7. 6 m Soil profile is given in…

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

n=1

Calculate the design moment strength of section shown in Fig(2),
and check the ACI Code requirements. Given f'e = 24 MPa and fy=370 MPa.
h= 500 + 10 × (n)
b=295 + 5 x (n)
Where: (n) is Student number
Fig. 2
h
As 325
As 628
b
65
90

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Subject: STEEL DESIGN Problem 2: A W 250 x 167 is used as tension member and the web is connected to a two gusset plates by 18 mm bolts as shown in Figure ST-009. Use A 36 steel with Fy = 250 MPa and Fu = 400 MPa. Hole diameter is 3 mm larger than the bolt diameter. I 40 80 80 150 PL 12 mm x 180 mm Properties of W 250 x 167: A = 21,200 mm² d = 290 mm br=264 mm t = 31.8 mm tw = 19.2 mm Figure ST-009 1. Compute the allowable strength of the tension member by ASD. 2. Compute the design strength of the tension member by LRFD. 3. Is it safe to carry the above load combinations according to ASD? 4. Is it safe to carry the above load combinations according to LRFD? 5. Compute the allowable strength of the tension member for block shear by ASD. 6. Compute the allowable strength of the tension member for block shear by LRFD.
OP N C What is the shear resistance of a universal beam (UB) with the following dimensions [EC3 Section 6.2 Resistance of cross sections]: Cross sectional area A = 105 cm² Height h = 584.6 mm Flange thickness t = 11.4 mm Flange width b = 213.2 mm y-y Web thickness tw = 7.8 mm Root radius r = 12.7 mm Yield strength fy = 355 N/mm² Calculate the shear resistance and give your answer to the nearest whole kN. Do not include units in your answer.
A built up section shown consists of A992 steel made from plates fully welded together. The flanges consist of PL16×380 and PL12×500 for the web. Fy = 345 mPa. Which of the following best gives the value of the section modulus? PL16x380 O 935x10^6 mm^4 3,514x10^3 mm^3 O 550x10^3 mm^3 O 3,887x10^3 mm^3 PL12x500
A column section is fabricated by welding a 12 mm x 150 mm cover plate to the top of a W 18 x 65. Assume that the components are connected in such a way that the member is fully effective. Length of column is 6.0 m. Properties of W 18 x 65 A = 13323 mm2 d = 466.09 mm Ix = 445 x 106 mm4 Iy = 23 x 106 mm4rx = 190.25 mm ry = 24.93 mm Fy = 345 MPa bf = 192,79 mm tf = 19.05 mm tw = 11.43 mm Zx = 2179 x 103 mm3 a. Determine the critical slenderness ratio of the built-up column section. b. Determine the design and allowable strength of the built up section based In flexural buckling. (kN)
A column section is fabricated by welding a 10 mm x 100 mm cover plate to the top of a W 18 x 65. Assume that the components are connected in such a way that the member is fully effective. Length of column is 4.6 m. Properties of W 18 x 65 A = 13323 mm2 d = 466.09 mm Ix = 445 x 106 mm4 Iy = 23 x 106 mm4rx = 190.25 mm ry = 24.93 mm Fy = 345 MPa bf = 192,79 mm tf = 19.05 mm tw = 11.43 mm Zx = 2179 x 103 mm3 a. Determine the critical slenderness ratio of the built-up column section. b. Determine the strength of the built up section based n flexural buckling. (kN in LRFD).
The truss is made from A992 steel rods each having a diameter of 0.9 in .(Figure 1) Part A Determine the vertical displacement of joint C. Express your answer to three significant figures and include the appropriate units. ? (Ac)vert = Value Units Figure Submit Request Answer < Return to Assignment Provide Feedback C 60° 60° 12 kip 6 ft B
PROBLEM The centroid of the T-section shown is 2.5 inches above the base. What should be the value of b to satisfy this condition? Input value only without the unit, 1" 8" 1" b
Problem 4.8 The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm². Part A Determine the magnitude P required to displace the roller to the right 0.28 mm. Express your answer to three significant figures and include appropriate units. Di Submit μA P = 0.09224 mm Previous Answers Request Answer ? 0.8 m 0.8 m - 5 kN 0.6 m-
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
For the truss shown in the figure, estimate the horizontal displacement at joint H. The area (A) and the modulus of elasticity (E) of each bar is 0.5 in2 and 29000 ksi, respectively. Summarize your results in the following order. Member AB BC CD DE EF FG GH AH BH CH CG CF DF T 12 ft 2k B G C D 10 ft-10 ft- 10 ft-10 ft
The figure as shown below is a rigid bar (ABCD) which was supported thru pin at B. Two bars was also connected, Bar CE and Bar DF with corresponding cross-sectional area and Modulus of Elasticity. If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm. with drawing and complete solution
A wide flange section is used as beam to support a concrete floor system. The beam is simply supported over a span of 6m. The properties of the section are given as follows:Depth, d = 498mmWeb thickness, tw = 56mmMoment of Inertia about x-axis, Ix = 3417 x 106 mm4Section Modulus about x-axis, Sx = 13730 x 103 mm3Self-weight, wself-weight = 7.32 kN/mAssume the beam is laterally supported over its length with its allowable stress in bending is 0.66Fy and its allowable shear stress is 0.40Fy assuming direct shear stress is used as basis instead of flexural shear stress. The allowable deflection is set at L/360. Use A36 steel with Fy = 250 MPa. (a) Compute for the safe uniform load (w) without exceeding the allowable shear stress. (b) Compute for the safe uniform load (w) without exceeding the allowable bending stress. (c) Compute for the safe uniform load (w) without exceeding the allowable deflection.