Calculate Required size of core and calculate number of turns in primary and secondary for small transformer whose, Output (secondary) voltage (Vs or Vo)= 12. V Output (secondary) current Io = 3 A Primary voltage, Vp = 230 V Supply frequency, f- 50 Hz Assume efficiency, 90%

Calculate Required size of core and calculate number of turns in primary and secondary for small transformer whose, Output (secondary) voltage (Vs or Vo)= 12. V Output (secondary) current Io = 3 A Primary voltage, Vp = 230 V Supply frequency, f- 50 Hz Assume efficiency, 90%

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.3P: Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source...

See similar textbooks

Related questions

Q: Reduce the block diagram below into single transfer function.

A: first draw the signal flow graph then using the mason's gain formula calculate the transfer function…

Q: find the power dissipated in the 6 resistor.

A: As in the above circuit resistances are in parallel and in series so, We will be using following…

Q: 1. For the circuit given below plot the output waveform indicating positive and negative peak…

A: We have analyzed the circuit in the positive and negative half cycle. In the positive half cycle…

Q: (b) (c) ܙ ) - M m ܐ | ܤ | ܐ ܐܠ 3 t .. ܝ

A: 1. When a PN junction is in forward biased mode Then current flowing through transistor is…

Q: av + Switch Iks I malt

Q: The load per phase of a balanced 30 wye connected load is 8 + j6 Ohms per phase. This is connected…

A: For 3-phase supply, if they provide the voltage without saying line ya phase, then normally that is…

Q: The input-output relation of a system at initial rest is given by, dx (t) + 2 x (t) ¹+ 3y(t) =…

Q: 9. Which of the following equation represents mass semiconductors in electronic circuits? action law…

A: The correct option along with the explanation is provided in the following section.

Q: 2. The load per phase of a balanced 30 wye connected load is 8 + j6 Ohms per phase. This is…

A: In the given system, the load and source are balanced,so we can do the calculations of on per phase…

Q: Find the result of the subtraction using 2’s complement method. A= 110101 B= 101000 a) A -B b) B - A

A: 2's complement of some binary number is got by adding 1 to the 1's complement number. All the…

Q: Refer to Figure 16a and note that, when switch S1 is in the position A1 VCS =0V and the JFET is on…

Q: For each of the transfer functions shown below, find the locations of the poles and zeros, plot them…

A: The location of pole and zero can be obtained by equating the numerator and denominator part to zero…

Q: Circuit 4 Referring to the EWD, add a front map light circuit to the basic system circuit below Dome…

A: 1) b. 12 always. As 1 is directly connected to the battery and as it's voltage is 12v '1' will be…

Q: 3. The radar in which both transmission and reception is done using the same antenna are called:

A: The correct option along with the explanation is provided in the following section.

Q: 3-1. A certain op-amp has the following de and very low-frequency parameters: dc open-loop gain…

Q: Electrical Engineering. What is the function of MCB. Write two advantage and disadvantage of MCB

A: An MCB is a type of electrical switch that operates automatically to guard against overload or short…

Q: If the impedance Z1 = 0 +j10 and the impedance Z2 = 10-j10 are connected in parallel, the equivalent…

A: Given, Two impedance connected in parallel are, Z1=0+j10 ΩZ2=10-j10 Ω

Q: Subject: Fundamental of Electronics Question: Do Theoretical Calculation to get value for Vclipper

A: Note: All the circuits are named incorrectly. In the solution, we will use the correct names for the…

Q: Briefly explain what you mean by discrete system and continuous system.

A: Continuous system: Continuous systems seem to be ones in which output & input signal are…

Q: 2) The three-phase, 50 Hz, 100 km long power transmission line has a resistance per unit length of…

A: Given, Frequency=50Hz, L=Length of transmission line=100Km R=Resistance=0.1×100=10Ω,…

Q: The total charge of a uniform insulating sphere is 12.84 nanocoulombs. If the radius of the…

A: We need to find out the electric field due to sphere

Q: I3 An infinite length wire carrying current 10A is positioned along the x-axis . a point is located…

A: By amperes law, We Know that magnetic field due to infinitely long line at distance r is…

Q: Obtain the form factor of a half rectified sinewave mm sine kn -ot

Q: What is the purpose of an Amperian Path in Ampere's circuital law? 1 Computation of magnetic field…

A: Ampere's law relates the integrated magnetic field intensity around a closed loop to the current…

Q: For the below circuit what will be the time constant? ww t=0 9 V 8 Ω 3 μF

A: Given circuit,

Q: Vas Ic=1mA. If R = 400 52 and R = 5 k2, find AM and f by using the Miller's theorem.. Rus B www + HH…

Q: 6. In a parallel circuit the voltage drop across each branch is always equal to the source voltage.…

A: The answers to question number 6 and 7 are wrongly marked. 6. Answer: True Explanation: In a…

Q: 1.The logic OR function when expressed in algebraic terms is analogous to the ? 2.A 4 input NOR…

Q: m(t)=Amsen(comt) Figura 1 MODULADOR AM (DSB-LC) Vsalida(t) vc(t)=Acsen(wet)

Q: Derive the equation for impedance and phase shift for series RLC circuit connected to the AC…

A: A series RLC circuit is formed by connecting a resistor, inductor, and capacitor in series across a…

Q: Using the Routh Hurwitz Criterion, determine the stability of the following system: R(s) 0.7(s+ 0.1)…

Q: 10.55 Find I, in the network in Fig. P10.55. 2:1 36/0°v(+ ww 6Ω Figure P10.55 -j8 Ω Ideal 12 Ω | j4Ω…

Q: Using Nodal analysis, find V1 in Volts if Is = 4.6 A and R = 8.5 Ohms. Give answer in 2 decimal…

A: The given circuit diagram is shown below: It is given that: IS=4.6 AR=8.5 Ω

Q: Find the spectrum for the wave forms: 1 + 8 Sin (Gut) "t-2 @ vot

A: Given: v(t)=π(t-24)+8sin(6πt) To find the spectrum of the signal, we'll compute the Fourier…

Q: A normal transformer has a nominal 60 kVA. The nominal primary and secondary voltages are 600 V and…

A: Given data : Transformer rating P=60 kVA Primary voltage V1=600 V Secondary voltage V2=120 V

Q: 4. Which of the following is the correct relationship between temperature (T) and mobility (u) of…

A: The solution is provided in the following section.

Q: Question 3 a) The Fermi level of a solid-state body is the thermodynamic work required to add one…

A: (a) Fermi level: The band nearest to the Fermi level is the valence band and conduction band in…

Q: . The expression of an AM modulated wave (DSB-LC) is: , vAM(t)=[5+ 4sin(3000π t)]sin(1x10^6π t) a)…

Q: Find the voltage across the capacitor terminal at time 1 ms for the circuit below. ww R 10 Ω |1 100…

Q: se the best statement that explains why a constant magnetic field cannot do work on a mov O The…

A: The fact that magnetic force do no work is an elementary and direct consequence of the Lorentz force…

Q: An EM wave progating in a certain medium is described by E = 33.3 sin(1002.4 x 10°t - 4.4x)az V/m…

A: Given data, An EM wave propagating in a certain medium, E=33.3sin1002.4×106t-4.4xaz V/m

Q: Use the diagram below for questions 11-17 12V 22 11. If current flow at point F is 3 amps and…

Q: For answers related to this problem just type the value without the units in the form . The wave in…

A: The Peak amplitude of modulator and the unmodulated carrier wave can be calculated by using the…

Q: - Determine the effective isotropic radiated power for an antenna with a directivity D = 43 dB, an…

A: Given Data: D = 43 dB efficiency = 75 % Pin = 50 W

Q: Circuit 6 The ignition switch is located on the battery side of the fuse. Power is not supplied to…

A: 1. b) fusible link will blow out when ignition switch is on as high short circuit current flows. 2.…

Q: A A. B. C. D. of the galvanometer shows that the flow of induced_ momentary deflection, current…

A: Galvanometer deflection indicates the current is flowing in the conductor.

Q: 3. The radar in which both transmission and reception is done using the same antenna are called: a)…

A: The correct option, along with the explanation, is provided in the following section.

Q: Determine the magnitude of force per 1.1 m length of a pair of conductors of a direct current line…

Q: Determine the voltage across the

A: Given- Coil resistance= 10 ohm Coil inductance= 15 Henry Series resistance= 15 ohms DC source…

Q: The total charge of a uniform insulating sphere is 14.16 nanocoulombs. If the radius of the…

A: The total electric flux, according to Gauss's law, is equal to the contained charge divided by the…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Calculate Required size of core and calculate number of turns in primary and secondary for small transformer whose,

Output (secondary) voltage (Vs or Vo)= 12. V

Output (secondary) current Io = 3 A

Primary voltage, Vp = 230 V

Supply frequency, f- 50 Hz

Assume efficiency, 90%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
opper losses Which of following is a variable loss in a transformer? O Constant loss O Eddy current Hysteresis losses O Copper loss
How do i calculate secondary current in transformer analysis
In this Center tapped transformer Find the peak voltage of V1 and V2, RMS voltage of V1 and V2, and Peak to peak voltage of V1 and V2
In no load phasor diagram of practical transformer, the magnetizing current Imag is with primary voltage Vp. O Leading by 30° O 90° out of phase O In phase O Lagging by 60°
High permeability O Low reactance O Low permeability The purpose of the no-load test in the transformer is to determine O Input voltage Core loss O Copper loss O Turn ratio
A single-phase 500 V/100 V, 50 Hz transformer has a maximum core flux density of 1.5 T and an effective core cross-sectional area of 50 cm2. Determine the number of primary and secondary turns.