Thank you Cables in a suspension bridge are subject to twisting, that causes shear stresses.With this phenomenon, the effect of shear stresses on the cable is bestdescribed by? *Fibers move together in the tensile direction.Fibers slide over each other.Fibers move apart in all directions.Fibers move together in all directions.

Answer - B Fiber slide over each other

Cables in a suspension bridge are subject to twisting, that causes shear stresses. Vith this phenomenon, the effect of shear stresses on the cable is best described by? * O Fibers move together in the tensile direction. O Fibers slide over each other. O Fibers move apart in all directions. O Fibers move together in all directions.

Cables in a suspension bridge are subject to twisting, that causes shear stresses. Vith this phenomenon, the effect of shear stresses on the cable is best described by? * O Fibers move together in the tensile direction. O Fibers slide over each other. O Fibers move apart in all directions. O Fibers move together in all directions.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 20CQ

See similar textbooks

Similar questions

Explain in detail the relationship between stress and strain for non linear elastic material . Also explain why non linear elastic material does follow Hook's Law.
A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest. If it is subjected to a tensile load of 6,000 lbs, what will be the tótal deformation of the bar if it has a modulus of elasticity E= 28.5 x 10^6 psi. %3D O 0.1378 inches O 0.1338 inches O 0.1352 inches O 0.1364 inches O 0.1423 inches
} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm?. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Saterat Eaxial Fatuminum™ 3000 N A-500 mm² A=500 mm² Fatuminum=? 3000 N Steel Aluminum
Tell the strengths of the forces on the bars and their types, whether they are tensile or compressive as well. Follow the figure below.
A 10 inch long silver wire is stretched to a total length of 11.50 inches. Find the value of strain
Q.2) A steel plate is subjected to a force system as shown below. Replace the given force system by a resultant force and locate intersection of its line of action with the x-y plane. X-- 45 lb 2.5' 60 lb 4.5' 3' 55 lb 50 lb 2₁- 30 lb 5' 4' 70 lb y
Volumetric Strain Question 5: The principal stresses at a point in an elastic material are 60 N/mm² tensile, 20 N/mm² tensile and 50 N/mm² compressive. What is the volumetric strain by considering Young's Modulus as 100 x 103 N/mm² and μ = 0.3?
1. A circular rod of diameter 20 mm and 500 mm long is subjected to a tensile force 45 kN. The modulus of elasticity for steel may be taken as 200 Kn/mm². Fine stress, strain and elongation of the bar due to applied load.
Figure 1 above represents a Warren truss of a bridge. If it is subjected to the loading on it: a) Determine the reactions of the truss above. b) Determine the forces in all the members. C) What is the critical member with regards to tension and why? d) What is the critical member with regards to compression and why? please show all working in all details, please ensure to complete all answers and explain as it requires in the question. please this is very urgent and needs proper solution to the question.
To reinforce a column in an existing structure, two channels are welded to the W 12 x 50 column section as shown in the figure. Effective length of column with respect to each axis is 4.8 m. Kx = Ky = 1.0 Properties of W12 x 50 A = 9484 mm2 rx = 131.57 mm ry = 49.78 mm Ix = 164 x 106 mm4 Iy = 23 x 106 mm4 Fy = 345 MPa d = 309.63 mm Properties of C6 x 13 A = 2471 mm2 Ix = 7.24 x 106 mm4 Iy = 0.44 x 106 mm4 bf = 54.79 mm x = 13.06 mm (centroid from the outer side of the web) a. Determine the critical slenderness ratio. b. Determine the design strength of the column section. (kN in LRFD)
The strain in member AB was measured to be 9 × 10^−4. If the member is an ? 3 × 3 × 1/4 of A36 steel (refer to AISC Table 1-7, next page), determine thefollowing:a. What is the change in length in inches?b. What is the force in the member?Note: For all structural steels: modulus of elasticity, ? = 29,000 ksi
Answer completely and legibly about stress and strain