c) Illustrate the results of the viscosity test of the above motor oil then fit the viscosityfunction of temperature to the following logarithmic quadratic correlation as describedbelow. Find the values for the constants a, b, and c. Take Ho at To = 0° C.(4) - )To+ cToIn- a + bMod) What is the viscosity of the used motor oil at 280 K, 305 K and 320 K? You can use theabove equation Task 3: Fluid Mechanics Lab MetersYou studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50Motor Oil viscosity. Follow the following steps to do your task.HEATING UNITTHERMOMETERLIQUID BATHFluidCONTAINERCORK60 CC-ŘESERVOIRFigure 4: Schematic for SAYBOLT viscometer.

“Since you have asked multiple questions, we will solve the first question for you. If you want any…

c) Illustrate the results of the viscosity test of the above motor oil then fit the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Take Ho at To = 0°C. To + c To In- = a + b Mo

c) Illustrate the results of the viscosity test of the above motor oil then fit the viscosity function of temperature to the following logarithmic quadratic correlation as described below. Find the values for the constants a, b, and c. Take Ho at To = 0°C. To + c To In- = a + b Mo

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the fluid used for prototype. During testing of the model, if viscosity and gravity forces are predominant, find the scale ration, velocity ratio and discharge ration
! Required information The dynamic viscosity of air at 20°C is u≈ 1.80E-5 Pa-s. Estimate the viscosity of air at various temperatures by the below mentioned methods. Determine the viscosity of air at 500°C by the Law of Corresponding States. E-5 kg/(m.s)
A Newtonian fluid with absolute viscosity (Greek mu) flows past a flat surface. Due to the no-slip boundary condition, the velocity profile, u(y), develops near the surface and is given by u/U (shown in image provided) where the constant parameters U and delta have dimensions of velocity and length respectively.a) Develop an expression for the shear stress acting in any horizontal plane.b) Determine the shear stress acting on the surface at y = 0 and again at the edge of the boundarylayer, y = delta. (Express your answers in terms of Greek mu, the outer velocity U, and the boundary layer thickness delta.)
2. Experimental measurements of relationship between velocity gradient and shear stress for different liquids are shown in the table given below. a) Plot the data on Excel and determine the fluid types. (Show your graph!) b) Which model do you use to describe the data? Specify the ranges of values for the coefficients. Velocity gradient Shear stress Fluid A Fluid B Fluid C 0.2 2.60 7.80 61.55 0.5 5.80 17.40 63.67 0.95 10.51 31.53 66.45 1.4 14.52 43.56 69.30 1.9 21.02 56.75 72.89 2.45 28.22 64.91 77.60 3.05 31.50 69.30 80.38 3.7 38.91 71.98 84.50 4.35 45.21 76.86 88.81 5.05 51.71 80.15 93.78
Fluid Statics Please provide a complete and readable solution for the problem if necessary and an explanation. Thank you!
The dynamic viscosity of water is 0.001 N-s/m2. Determine the kinematic viscosity in English system. Calculate the equivalent kinematic viscosity in stokes. (Hint: 1 stoke = 1 cm2/s) Answer the situations with complete solutions. Write your final answer in two decimal places. please input the correct unit and box final answer thank you
1. To determine the dynamic viscosity of a liquid you take repeated measurements of the liquid density and kinematic viscosity. These data are summarized in the following table: Avg. measurement Total Uncertainty P 999 kg/m³ ±0.5% V 1.23 mm²/s ±0.01 mm²/s kg Ns What is the dynamic viscosity? Give dynamic viscosity in units of; which is the same as ms 2. Determine the absolute and relative uncertainties in the dynamic viscosity.
The most influencing parameter on Reynold number is: choose one 1-Fluid density 2-Fluid velocity 3-Fluid viscosity 4-None of above
The absolute viscosity of the liquid is 1.8 x 10^-3 Pa-s and its SG is 2.50. Compute the equivalent kinematic viscosity in m2/s (decimal form)
In your new position at the fluid mechanics laboratory, you are required to do a to d branching. a) You perform a set of testing to measure the viscosities for various fluids: Engine oil, aluminum, zinc, water and 1:10 ratio of (corn starch: water). Pick and justify one type of viscometer for each type of fluid then, justify why a specific viscometer will not work for a type of fluid as follow: I would use I would not use Engine oil Aluminum Zinc Water Cornstarch solution Justify your answers in one statement each for each of the boxes in orange (total of 10 sentence b) For water you obtained the following data: Temperature [K] 300 310 318 340 Viscosity [cP] 0.8509 0.6913 0.5958 0.42 What is the viscosity of water at 290 K, 312 K and 350 K? You may use the following equation: ln ?? ???? = ?? + ?? . ???? ?? + ?? . � ???? ?? � 2 Where a = - 1.94, b = - 4.8, c = 6.74
Q) The velocity v (m/s) of air flowing past a flat surface is measured at several distances y(m) away from the surface. Use Newton'sviscosity law to determine the shear stress t (N/m³) at the surface (y=0). dv 'dy Assume a value of dynamic viscosity =1.8* 10- N.s/hm² y, m V, m/s 0.002 0.287 0.006 0.899 0.012 |1.915 0.018 3.048 0.024 4.299 (r-7) Use two forward đifference approximations for h=0.006. Estimate the approximate percent relative error, &. b- , (t=?) Use two forward difference approximations with a step size of 0.012 (h=0.012). Estimate the approximatepercent relative error, , e.. (r-?) ApplyRichardson extrapolation. Estimate the approximate percent relative error, & (r=?) Use unequally spaced three data and the first-derivative of a second-order d- Langrange polynomial to evaluate the derivative (y=0) and shear stress. Estimate the approximate percent relative error, Eg Compare the approximate estimates of the error ([ed ) for the formulas used.