(c) (i) Flow over an ogee spillway creates oscillating hydraulic jump at its toe. Height of water level from toe of dam to crest of spillway is 32.80 ft. If the flow is 25,000 L/s, determine excess water over 4 m width of spillway crest.

(c) (i) Flow over an ogee spillway creates oscillating hydraulic jump at its toe. Height of water level from toe of dam to crest of spillway is 32.80 ft. If the flow is 25,000 L/s, determine excess water over 4 m width of spillway crest.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In a furrow irrigation system, the following information is giv . • Length of a furrow = 200 m

A: Given:- length of furrow=200m Inflow=1.5l/s To find:- Irrigation time

Q: lexalexatagal 24 m 24 m 16 mm A beam of the cross section shown is extruded from an aluminum alloy…

A: Given data We are given that Yield stress σγ = 250 Mpa Ultimate stress σu = 450 Mpa Factor of…

Q: For the mechanism, shown on the figure, pc = const = 5 $¹, OA=BC=0,3 m, AB-0,6 m. Determine: a)…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: 5.12 Draw the shear and bending-moment diagrams for beam and loading shown, and determine the…

A: Considering the moment at G: ∑MG=0-16C+(36)(400)+(12)(1600)=0C=1800 lb∑Fx=0-C+Gx=0Gx=1800…

Q: What does the stress in a composite beam depend on?

Q: UPVOTE WILL BE GIVEN. Please write the complete solutions and box the final answer. Use 4 decimal…

Q: For a 3-hr unit hydrograph, determine a 3-hr S-Curve? Time (hours) 0 Q (cfs/inch) 6 12 18 24 100 40…

A: Given data:- Time (Hours) 0 6 12 18 24 Q (cfs /inch) 0 30 100 40 0

Q: A water treatment plant has a flow rate of 0.6 m³/s. The settling basin at the plant has effective…

A: Given- flow rate=0.6 m3/sdimensionsL=20 mH=3 mB=6 msettling velocity=0.004 m/s

Q: RD RA R. = 40 KN VD1² VD2 = M B1 82 2 m Mg2 MB1 hinge t-4m. Vpz KN KN 2 kN/m KN KN KN KN kNm kNm kNm…

Q: A simply-supported beam with length, L = 9 m, is carrying a downward uniform load, w = 48 kN/m…

Q: How to find the Radius of the simple curve ?

A: Given, Station at PC = 596+43.953 Station at PT = 602+51.327 Deflection angle (△) = 70o

Q: Results of a standard Proctor compaction test on a silty sand are shown in the below figure. Dry…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: 1. A circular flat plate of diameter 120 mm and thickness 10 mm is constructed from steel with E =…

A: Given values: Circular plate, diameter, d = 120 mm thickness, t = 10 mm E = 208 GN/m2 Uniform…

Q: M M M 13.9kft СЕ 4.64 kips M 9º MB 30 kips KN KN E E ·6² 6². 17.97kips 40kips E kNm kNm kNm 4…

A: Given data:- Below diagram is given in question;

Q: A short post carries a downward load P = 133 kN as shown in the figure. Due to its eccentricity from…

Q: If the lake level upstream from a spillway is 55 m above the channel floor at the base of the…

A: Given data: b=30 m Q=1000 m3/s

Q: Mathematical project selection methods include which of the following.

Q: The rotation of the 0.9-m arm OA about O is defined by the relation Eq. (1), where is θ expressed in…

A: Answer We are given θ = 0.15t2 (θ in radians and t in sec ) r = 0.9-0.12t2 (r in meter and t in…

Q: Q- (D) A building is fetching an annual rent of Rs 1,80,000/-. The purchase desires to get 5% return…

A: given- Annual rent=Rs 1,80,0005% return on capital

Q: Determine the magnitude of the force which member CD exerts on the pin at C. A B (21/0.53 m Answer:…

A: Determine the magnitude of the force which member CD exerts on the pin at C.

Q: sieve 100 Percent finer than the #40 sieve 92 Percent finer than the #200 sieve

A: We knowGI=0.2F200-35+0.005F200-35LL-40+0.01F200-15PL-10

Q: 3. Determine the resultant force of the following loading diagram. -6 ft -8 ft 150 lb/ft

A: Resultant force = equivalent load of loading diagram.

Q: Determine the axial stresses of the following truss members: (JJ, Co. C Use 400mm² members in For…

Q: Solve for the magnitude of the axial forces of members DJ, FJ, and FG. Indicate whether the member…

Q: Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member…

Q: Cite some practical importance of determining water hardness in the industry

A: It has been asked in the question to list why we determine hardness in the factories.

Q: RA M RA Rc= 4 kN -3 m- 24 E ME 3 m m. 2 kN-m Vc Rc MC2 Mc₂ kNm KN KN 료 KN 6m RD

Q: 3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the…

Q: Question 4 a) Define and explain using sketches, metacentric height, stable and unstable equilibrium…

Q: Methods of adjustment of chains of triangles. explain each method

A: In this question it has been asked in the question to explain Methods of adjustment of chains of…

Q: In a cantilever of span L subjected to a concentrated load of W acting at a distance of 3 from the…

A: given- cantilever beamspan=Lconcentrated load=W at distance of L/3 from free end

Q: (b) Fatigue cracking and stresses on asphalt structure induced to an interlaced cracking pattern and…

A: Fatigue cracking is a type of failure on asphalt pavement that occurs due to the cooling of pavement…

Q: A two-dimensional conduit has the velocity distributions shown in figure (a) and (b). Calculate the…

Q: Using plastic analysis and collapse mechanism, analyze a 10-m long propped beam loaded with…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: Fy= 50 Ksi, Fu= 65ksi Select the lightest W10 section available to support working tensile loads of…

A: Given : Fy= 50 Ksi, Fu= 65ksi Select the lightest W10 section available to support working tensile…

Q: Find the reactions at support and force in member CD

A: Given, A truss carried a point load of 1kN at point D Let, RA&RB be the vertical reaction at the…

Q: Using a 30-m tape that is 0.05m too long, the laid-out distance from X to Y is 140.42m. What is the…

A: Let's say nominal length of the tape L = 30m Actual length of the tape L' = (30+0.05) = 30.05 m…

Q: From the figure below, Compute elevations of main and full stations on a concave curve? That has…

A: Given data:- Below figure is shown;

Q: 25. Degree of saturation of a natural soil deposit having water content 15%, specific gravity 2.50…

A: given- water contentw=15%specific gravity G=2.50void ratio e=0.5

Q: 13. Free settling of sludge is 0.25 cm/min. Using an original height of 25 cm, the sludge settled to…

Q: Using Work and Conservation of Energy, determine what is ask in the problem. PROBLEM 1: A 1270 kg…

Q: In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a…

Q: Determine the force in member BE of the truss. State if the member is in tension or compression. Ap…

Q: G H A 5 kN/m 81 8 m L I B 3 kN/m 8 m K J C 5 kN/m 8m F E D

A: It has been asked in the question to Draw the approximate moment diagrams for each of the five…

Q: Determine the maximum moment on a 5m simply supported beam if two 12 kN load, 2m apart, is to pass…

A: Since the maximum moment always occurs under a wheel loads, it can be said that the resultant of the…

Q: 6. The beam shown in the figure carries DL= 10.5kN/m (including its own weight) and LL = 13.5kN/m.…

Q: uation 4: The lap splice shown will develop a full strength as shown in the figure. Using E70 el e…

A: I have solved your problem

Q: Answer for ME, VE, and Vc

A: Find ME, VE and VC

Q: distance of 3.6 m and a vertical distance the figure what is the rate of flow?

Q: n. brick is compressed lengthwise by a force P, as shown. If the ultimat stress is 3600 psi, what is…

A: Area for normal stress =4×2.5=10in2Area for shear stress =8×2.5=20in2

Concept explainers

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.

Question

(c)
(i)
Flow over an ogee spillway creates oscillating hydraulic jump at its toe.
Height of water level from toe of dam to crest of spillway is 32.80 ft. If the
flow is 25,000 L/s, determine excess water over 4 m width of spillway crest.
Tai

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Explain the variation in head loss if the discharge of the channel bed varies. within the open channel (Hydraulic jump). Need ASAP. Thank you.
H.W: Design ogee spillway for a concrete gravity dam and find the maximum flood discharge could be disposed of safely to the downstream. It is having downstream face sloping at (0.85H: IV), the height of spillway crest is kept at (0.85H:1V), the height of spillway crest is kept at level (310 m), the average river bed level at the site is (190 m), the spillway length consist (5) span having clear width (12 m) each with pier thickness=3m, k,-0.01, k.-0.1, C-2.2. If the D/S crest profile is given by: X¹5-25 y. and the U/S by: 0.724 (x+0.27 18 +0.126 H-0.4315 H375 (x+0.27 H₂) 0.625 Neglect the approach velocity head
Q(2):A spillway carries a discharge of 22.5m³/s with the outlet velocity of 15m/s at a depth of 0.2m. Design the stilling basin and determine the jump efficiency?
5. In rectangular channel at a section P, it is required that the depth of flow is to be 1.4 m and the specific energy to be 2.8 m. The flow at section P is subcritical, critical, or supercritical flow? 10%
For the following spillway of Hd = 10 m , P = 25 m , L = 120 m g = 9.81 m/s2 , calculate the design flowrate Q = 5500- 7400 m3/s Q = 8000- 8400 m3/s Q = 3100- 3400 m3/s Q = 6000- 6400 m3/s
Design ogee spillway for a concrete gravity dam and find the maximum flood discharge that could be disposed of safely to the downstream. It is having downstream face sloping at (0.85H: 1V), the height of spillway crest is kept at (0.85H: 1V), the height of spillway crest is kept at level (300 m), the average river bed level at the site is (190 m), the spillway length consist of (5) span having clear width (10 m) each with pier thickness = 3 m, kp=0.01, ka=0.1, C=2.2. If: D/S crest profile is given by: X1.85 = 25y And the U/S: y = 0.724 (x+0.27 Ha)" 1.85 HO.85 + 0.126 H-0.4315 H375 (x+0.27 Hd) 0.625 Neglect the approach velocity head.
3- A rectangular channel has a width of 5 m, carriers a discharge of 24 m³/s with a depth of 3.2 m in Section 1. At a certain distance downstream (Section 2), flow experiences a smooth and gradual contraction to a width of 3.5 m and a bed raise of 0.5 m. Note: The energy loss is negligible. a) Calculate the flow depth in Section 2 without considering the bridge piers (v2) b) Calculate the flow depth in Section 2 with considering the minimum channel width (v.) c) Calculate the maximum diameter of the two bridge piers in Section 2 such that no backwater occurs for this discharge 0 B₁ Top View B₂ Yı Side View 1/2 4z
Section-B (i) Calculate the discharge over an ogee weir with coefficient of discharge equal to 2.4 at a head of 4 m. The length of the spillway is 80 m. The weir crest is 12 m above the bottom of the approach channel having the same width as that of the spillway.
1a) 2-m wide sluice gate in a rectangular spillway discharges 20 m³ /s of flow at a depth of 1.6 m. Hydraulic jump occurs downstream. Calculate : (i) Type of jump (ii) Height of jump (iii) Head loss (iv) Percentage of energy loss relative to initial energy.
HW1 // A stepped rectangular weir has the upper step 1m wide and 0.3m deep and the lower step 0.6m wide and 0.5m deep. Calculate the discharge when the water level just touches the top edge of the weir. cd= 0.6 HW2 // What is the equation for the compound weir below? HW3 // Water flows at a rate of 5 m3/sec in a rectangular channel of width 10m. the normal depth of flow in channel is 5m. if a sharp-crest weir of height 5m is installed across the channel, determine the new flow depth in the channel for the same flowrate? cd = 0.6 HW4 // A rectangular weir with 1.6 m width. How high should it be placed in a channel to maintain an upstream depth of 2.35 m for 0.4 m3/sec flow? 0.65 cd = (1+4)
A hydraulic jump is formed in a 5.0 meter wide rectangular outlet downstream of a control (sluice) gate. If the flow depth upstream of the gate is 9.0 meters and the discharge is 150 m^3/s, find (1) the flow depth just downstream of the gate, (2) flow depth downstream of the jump, (3) the head losses of the jump.
The head over a sharp-crested suppressed weir is 0.59m. The length of the channel at the back of the weir is 4m and the height of the weir is 1.50m. Determine the coefficient of discharge and discharge over the weir. If the weir is submerged and the downstream water surface is 0.30m above the top of the weir, determine the discharged of the submerged weir. #hydraulics