3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.

3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Given data :

Q: o Given: A stepped shaft with the following properties Copper: A = 2 in² E = 16 × 106 psi Steel: A =…

A: Given Copper and steelArea and Elasticity modulus of copper is 2 in2 and 16×106 psiArea and…

Q: The shaft consisting of steel and aluminum segments carries the torques T and 2T. Find the largest…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: Determine the magnitude of the pin forc Assume W = 845 lb, a = 4.4 ft, b = 3.4 ft, r 1 W C Answer: A…

A: Given: Weight Distances Radius To find: Pin force at A in above figure

Q: Q.1: A shaft composed of segments AB, BC is fixed between the two walls at 4 and C and loaded as…

A: Given that: A composite shaft with 2kNm torque applied at B as shown-

Q: Determine the maximum torque T in kN.m without exceeding a shear of 70 MPa in steel and 50 MPa for…

A: 1. 10.44kn-m

Q: The internal diameter of a steel shaft is 70% of external diameter. The shaft is to transmit 3500 kW…

A: To determine: the diameter of the hollow shaft maximum angle of twist Given, Power to be…

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

Q: The shäft iš made portion made of steel and having a brass core. If it is fixed to a rigid support…

Q: 1. Determine the maximum torque Tin kN-m without exceeding a shear stress of 70 MPa in steel and 50…

A: Given, Gst = 83 GPa or 83000 MPa Gbr = 35 GPa or 35000 MPa

Q: 4.5m Bronze -3.5m Steel T 120 mm

Q: The shaft consisting of steel and aluminum segments carries the torques T and 3T. Find the largest…

Q: A steel pipe of 300-mm outer diameter is fabricated from an 8-mm-thick plate by weldingalong a helix…

A: Step 1:Step 2:

Q: ine the maximum load Pmax that may be supported by the st boo b B b

Q: The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G= 39 GPa). Knowing that portion CD…

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

A: Given data Diameter of brass rod (dB) = 32 mm Diameter of steel tube (ds) = 50 mm Gs = 2GB T =…

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

A: To determine the maximum shear stress developed in steel.

Q: A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

Q: Refer image below

A: Given data: Steel:L=2 mDi=70 mmDe=100 mmBronze:L=1.5 mD=70 mm

Q: A force of P₂ = 1000 N is exerted on control arm BC, which is secur assembly are a = 120 mm and b =…

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Angle of twist The angle of twist for a shaft subject to torsional loading is the rotational angle…

Q: The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the…

Q: 600 400 600 800 Gl P2 P3 E F Tha at y pnywty A - 100 mm" E- 200 GPa A- 150 mm E- 200 GPa A130 mm E-…

Q: 2. The stepped steel shaft camies the torque T. Determine the maximum allowable magnitude of T if…

A: Finding out maximum torque required in shaft.

Q: Determine the magnitude of the pin force at A. Assume W = 875 Ib, a = 2.8 ft, b = 2.1 ft, r = 8 in.…

Q: A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in the…

A: Given:- A composite shaft fastened to rigid supports having Modulus of Rigidity as…

Q: Determine the magnitude of the pin force at A. Assume W = 810 lb, a = 3.7 ft, b = 2.5 ft, r = 7 in.…

Q: Determine the magnitude of the pin force at A. Assume W = 645 Ib, a = 3.7 ft, b = 3.0 ft, r = 8 in.…

Q: Determine the magnitude of the pin force at A. Assume W = 845 lb, a = 3.0 ft, b = 2.0 ft, r = 9 in.…

A: We have to find the value of magnitude of pin force at A. Given data is W = 845 lb, a = 3.0ft, b 2.0…

Q: A hollow shaft made of red-brass copper (G= 37 GPa, shear yield strength = 150 MPa) is sandwiched…

A: G = 37 GPa or 37000 MPaMPaNOTE : As per guidelines, first 3 parts are solved. Request you to post…

Q: A prismatic shaft consists of a solid brass rod of diameter 32 mm, which is inside a steel tube of…

Q: Current Attempt in Progress The compound shaft consists of a solid aluminum segment (1) and a hollow…

A: Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the…

Q: shear stress of 100 MPa in the bronze segment,

A: Given data- Diameter of rod (D) = 120 mm = 0.12 m Maximum shear stress(£) = 100 Mpa Length of bronze…

Q: The stepped steel shaft carries the torque T. Determine the maximum allowable magnitude of T if the…

Q: Determine the magnitude of the pin force at A. Assume W = 530 Ib, a = 3.6 ft, b = 2.9 ft, r = 9 in.…

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and…

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Solution:-The diagram is shown below, Given data,Torque(T)=200kN.mE=720GPaG=27GPaThe diameter of…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

3.9 The compound shaft consists of bronze and steel segments, both having
120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the
bronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for
steel and G = 35 GPa for bronze.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

civil engineering. need help.
Determine the maximum compressive bending stresses in the beam shown. Let P = 14 Note Answer in whole number I = 100 × 106 mm P kN/m 2. 130 mm A NA- B |= 4P 6 m Poy= 200 mm 2P kN 6 -X= 4m - 4P - GP
P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar AE is an aluminium alloy [EAE 70 GPa] with a cross-sectional area of AAE = 2,400 mm². Bar CF is a bronze alloy [ECF = 100 GPa] with a cross-sectional area of ACF = 6,000 mm². A downward load P=298 kN is applied at point B. Determine the normal stress created in bras AE and CF. E 2.9 m 0.8 m B P 1.5 m 3.3 m 1.2 m D
The stepped steel shaft carries the torque T. Determine the maximum allowable magnitude of T if the working stress is 12 MPa and the rotation of the free end is limited to 4°. Use G = 83 GPa for steel. T 80 inm 60 mm 4 m 3 m
P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar AE is an aluminium alloy [EAE 70 GPa] with a cross-sectional area of AAE = 2,400 mm². Bar CF is a bronze alloy [ECF = 100 GPa] with a cross-sectional area of ACF = 6,000 mm². A downward load P=298 kN is applied at point B. Determine the normal stress created in bras AE and CF. E 2.9 m 0.8 m B P 1.5 m 3.3 m 1.2 m D
Determine the force in each member of the truss loaded as shown below. State if the members are in tension orcompression. Tabulate the result of your analysis.
P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar AE is an aluminium alloy [EAE 70 GPa] with a cross-sectional area of AAE = 2,400 mm². Bar CF is a bronze alloy [ECF = 100 GPa] with a cross-sectional area of ACF = 6,000 mm². A downward load P=298 kN is applied at point B. Determine the normal stress created in bras AE and CF. E 2.9 m 0.8 m B P 1.5 m 3.3 m 1.2 m D
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torqueT that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 16 kips, F2 = 30 kips, and the normal stress in each rod must be limited to 18 ksi, determine the minimum diameter d1 required for rod (1).