By application of tensile force, the cross-sectional area of bar Pis first reduced by 30% and then by an additional 20% Another bar Q of the same material is reduced in cross-sectional area by 50% in a single step by applying tensile force After deformation, the true strain in bar Pand bar Q will, respectively be (a) 0.5 and 05

By application of tensile force, the cross-sectional area of bar Pis first reduced by 30% and then by an additional 20% Another bar Q of the same material is reduced in cross-sectional area by 50% in a single step by applying tensile force After deformation, the true strain in bar Pand bar Q will, respectively be (a) 0.5 and 05

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.26P: - 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v...

See similar textbooks

Similar questions

Question 2 A material with the given stress-strain curves is loaded in tension. Loading process COMPLETELY STOPS at B. When stress is 700 MPa and during the Re-load process, Find: 1. The longitudinal and lateral strain 2. Change in diameter a (MPa) 1000 800 dy= 600 300 150 D. 0.02 0.03 0.04 0.023 e(mm/mm) 0.01 €y = 0.006 7 MPa 90 80 70 60 50 40 30 20 10 T = 73 Oy =0.0013 = 0.54 0.73 Y (rad) Yu
After a fall, a 98 kg rock climber finds himself dangling from the end of a rope that had been 17 m long and 9.8 mm in diameter but has stretched by 3.1 cm. For the rope, calculate (a) the strain, (b) the stress, and (c) the Young's modulus. (a) Number i Units This answer has no units (b) Number i Units N/m^2 or Pa (c) Number i Units N/m^2 or Pa > >
2. The stress-strain behavior of a ductile cast iron of diameter 15.8mm and a gauge length of 60.80mm is shown below, 400 300 200 100 0.00 0.10 Strain Determine the following: (a) the modulus of elasticity (b) yield strength at a strain offset of 0.002. Stress (MPa)
A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying theload, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The lateral (transverse) strain is?
The relationship between true strain (ɛ-) and engineering strain (ɛ) in a uniaxial tension test is given as (a) & = In (1 + &7) (c) &7= In (1+ E) (b) ɛg = In (1- E) (d)= in (1- E) %3D %3D
A circular solid piece of rock is tested in a compression testing rig to examine its stress/strain behavior. The sample is 6 inches in diameter and 12 inches in length, with the compression load cell imposing a constant load of 10000 lbf equally at both the top and bottom of the rock sample. Assuming a measured reduction in length of 0.02 inches, find the compressive stress and strain of the rock.
O 0.6% 19% If an isotropic material has a Young's modulus of 85 Gpa and a Poisson's ratio of 0.25, calculate its shear modulus. Select one: O G = 29 Gpa O G = 34 Gpa G = 25 Gpa O G= 77 Gpa O G= 46 Gpa If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal BD. C 2 mm 4 mm EN DO O
A Copper specimen of circular cross-section is subjected to a tensile test. The data obtainedare:Length of Specimen = 329 mm;Diameter of Specimen = 39 mm;Load at Yield Point = 130 kN;Maximum Load = 219 kN;Load at fracture = 118kNDetermine the following:1) Find initial area of the test specimen2) Yield Stress3) Ultimate Stress4) Fracture stress5) Find the strain for 0.058mm elongation.6) Mark Yield stress, Ultimate stress and Fracture stress on a Stress-Strain diagram.
Q.1. In a creep test, a material with E = 600 MPa is initially loaded with a stress o, = 297 MPa. 1.5 hr after the initial loading, the strain in the material is measured to be 0.12, and after another hour, it is found to be 0.1832. What will be the strain in the material 3 hours after the initial %3D loading? How much time did it take for the strain to reach a value of 0.001?
A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.
A tensile bar is stressed to 250 N/mm2 which is beyond its elastic limit. At this stage the strain produced in the bar is observed to be 0.0014. if the modulus of elasticity of the material of the bar is 205000 N/mm2 then the elastic component of the strain is very close toa. 0.0004b. 0.0002c. 0.0001d. 0.00005 PLS EXPLAIN YOUR ANSWER THOROUGHLY