bläs 3 What is the maximum load that may (a) be applied to a specimen with a cross- sectional area of 130 mm2 without plastic deformation?(b) If the original specimen length is 76 mm, what is the maximum length to which it may be stretched without causing plastic ?deformation

bläs 3 What is the maximum load that may (a) be applied to a specimen with a cross- sectional area of 130 mm2 without plastic deformation?(b) If the original specimen length is 76 mm, what is the maximum length to which it may be stretched without causing plastic ?deformation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Part A The stress-strain diagram for a steel alloy having an original diameter of 0.40 in. and a gage length of 9 in. is shown in the figure below. (Figure 1) Determine the modulus of elasticity for the material. Express your answer to three significant figures and include appropriate units. HA ? Eapprox = Value Units Submit Request Answer Figure < 1 of 1 Part B a (ksi) 80 Determine the load on the specimen that causes yielding. 70 Express your answer to three significant figures and include appropriate units. 60 50 40 HA 30 20 Py = Value Units 10 € (in./in.) 0.04 0,08 0.12 0,16 0,20 0,24 0,28 O 0.0005 0.001 0.0015 0.002 0.0025 0.0030.0035 Request Answer Submit
The Highest load sustained druing an uniaxial tensile testing experiment is 7,500lb. If the original cross section has a diamter of 0.25in, what is the ultimate tensile strength? (please also make a drawing)
200 stress 『ち0 (MPa) 100 50 0.1 0-2 strain From the tensile stress-strain behavior for the brass specimen the diameter is 12-8 mm Calcalate the following: |- The Yield stress, 2-Modulus of elasticity. 3- The Tensile streuyth.
For a brass alloy, the stress at which plastic deformation begins is 345 MPa, and the modulus of elasticity is 103 GPa. Determine the following (a) What is the maximum load that may be applied to a specimen with a cross: sectional area of 130 mm2 without plastic deformation?(b) If the original specimen erngth is 76 mm, what is the maximum length to which it may be stretched without causing plastic deformation?
. From the tensile stress-strain behaviour for a casted iron as shown in the following curve. Please answer the following questions (1) Estimate the modulus of elasticity, (2) Calculate the change in length of a specimen with original length of 100mm that is subjected to a tensile stress of 300MPa. (Hint: Using the Hooke's law to get the strain.) 600 500 400 - 300 - 200 - 100 - 2 4 6. 8 10 12 14 16 Strain Strength (MPa)
The data below are for a thin steel wire suitable for use as a guitar string. Ultimate tensile stress: 1.8 x 109 Pa Young Modulus: 2.2 x 1011 Pa Cross-sectional area: 2.0 x 10-7 m2 In a tensile test, a specimen of the wire, of original length 1.5 m, is stretched until it breaks. Assuming the wire obeys Hooke’s law throughout, calculate the extension of the specimen immediately before breaking.
A high-strength steel was subjected to a tensile test. It failed under a stress of 1600 MPa with a total strain of 2.7%. (E = 200 GPa, oy = 1400 MPa.) (a) What is the ductility of this steel in terms of % elongation? (b) Estimate the diameter of a specimen made of this material that can carry a load of 5000 N while remaining in the elastic regime.
Part B The stress-strain diagram for a steel alloy having an original diameter of 1.0 in. and a gage length of 7 in. is shown in the figure below. (Eigure 1) Determine the load on the specimen that causes yielding. Express your answer to three significant figures and include appropriate units. HA Py- Value Units Submit Request Answer Part C Figure t oft> Determine the ultimate load the specimen will support. Express your answer to three significant figures and include appropriate units. NO 70 60 50 P. - Value Units 40 30 20 Submit Bequest Answer 10 (in/in) o G04 0m 12 016 020 024 02 a aa omams Provide Feedback
QI (a) A tensile stress is to be applied along the axis of a cylindrical steel rod that has a diameter of 7.5 mm. Given the Poisson's ratio, v is 0.30 and the modulus of elasticity, E of the steel is 207 GPa. Determine the magnitude of the load required to produce a 2.5 x10³ mm change in diameter if the deformation is entirely elastic. (b) Referring to the tensile test data tabulated in Table 1, answer the following questions: i. Select with justification the material that will experience the greatest percent reduction in area. ii. Select with justification which material is the strongest. Table 1. Tensile stress-strain data for several hypothetical metals Material Yield Tensile Strain at Fracture Elastic Strength Strength Fracture Strength Modulus (МРа) (MPa) (MPa) (GPa) A 310 340 0.23 265 210 100 120 0.40 105 150 C 415 550 0.15 500 310 D 700 850 0.14 720 210 E Fracture before yielding 650 350
An 820 MPa (145,000 psi) stress is applied to a specimen of 4341 steel alloy, which has a plane strain fracture toughness of 45MPa squareroot (m). If the greatest surface crack is 0.95 mm (0.03 in) long, will this specimen fracture as a result? Assume that the parameter Y is 1.22.
During stress-strain test, the unit deformation at a stress of 35 MPa was observed to be 167 x 10^-6 m/m and at a stress of 140 MPa it was 667 x 10^-6. If the proportional limit was 200 MPa, what is the modulus of Elasticity (GPa)? What is the strain corresponding to a stress of 80 MPa?
A specimen of steel 20 mm diameter with a gauge length of 200 mm is tested to destruction. It has an extension of 0.25 mm under a load of 80 kN and the load at elastic limit is 102 kN. The maximum load is 130 kN. The total extension at fracture is 56 mm and diameter at neck is 15 mm. Find (i)The stress at elastic limit.(ii) Young’s modulus.(iii) Percentage elongation. (iv)Percentage reduction in area. (v)Ultimate tensile stress.