Below is the stress (o = Ee) vs strain (e = 4) behavior of oxygen-free copper (OFC) wires (W8) at 293 Kand 77 K compared to conventional (Convt) copper wires of the same diameter at 293 K.900800W8, 77 K700W8, 293 K600500400Conv".wire,293 K3002001000 1 234 56 7 89.E [%]Engineering stress [MPa] Calculate the elongation (elastic) that can be achieved when a 560-mm long OFC wire is subjected to a stressof 185 MPa at 293 K.Al =mmFor the same length and stress, what is the elongation at 77 K?Al =mm

Answered: Image /qna-images/answer/35c66158-19d2-46d1-8caf-a91c6b49b567.jpg

Answered: Below is the stress (o = Ee) vs strain…

Below is the stress (o = Ee) vs strain (e = 4) behavior of oxygen-free copper (OFC) wires (W8) at 293 K and 77 K compared to conventional (Convtl) copper wires of the same diameter at 293 K.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an electrical discharge machining process, the breakdown voltage across inter electrode gap (IEG) is 200 V and the capacitance of the RC circuit is 50 μF. The energy (in J) released per spark across the IEG is T
Determine the resistance of a copper wire that has a cross-sectional area as 8.2 mm2. The length and the electrical resistivity of the copper wire are 77.1 m and 1.68 x 10-6 Qm. The resistance of a copper wire (in 2) A square cross-section v-notched specimen of height 75 mm has each side of 11 mm has been selected to perform Charpy impact test. Determine the notch thickness, if the cross-sectional area at notch is 104.5 mm2. Notch thickness (in mm)
A copper [E = 102 GPa, a = 16.8x10-6/°C] rod (2) is placed within a steel [E = 204 GPa, a = 11.3x10-6/°C] tube (1) of the same length. The two components are connected at each end by pins that pass through both the tube and the rod. The outside diameter of the steel tube is D₁ = 101 mm, its inside diameter is d₁ = 78 mm, and its cross-sectional area is A₁ = 3234 mm². The diameter of the solid copper rod is d₂ = 55 mm, and its cross-sectional area is A₂ = 2376 mm². Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by 44°C. Pin Steel Tube (1) Pin Copper Rod (2)
A copper [E = 96 GPa, a = 17.5x10-6/°C] rod (2) is placed within a steel [E = 192 GPa, a = 11.5×10- 6/°C] tube (1) of the same length. The two components are connected at each end by pins that pass through both the tube and the rod. The outside diameter of the steel tube is D₁ = 92 mm, its inside diameter is d₁ = 77 mm, and its cross- sectional area is A₁ = 1991 mm². The diameter of the solid copper rod is d₂ = 55 mm, and its cross- sectional area is A2 = 2376 mm². Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by 48°C. Pin Steel Tube (1) Pin Copper Rod (2)
A copper [E = 104 GPa, a = 17.1x10-6/°C] rod (2) is placed within a steel [E = 208 GPa, a = 12.2x10-6/°C] tube (1) of the same length. The two components are connected at each end by pins that pass through both the tube and the rod. The outside diameter of the steel tube is D₁ = 103 mm, its inside diameter is d₁ = 80 mm, and its cross-sectional area is A₁ = 3306 mm². The diameter of the solid copper rod is d₂ = 60 mm, and its cross-sectional area is A2 = 2828 mm². Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by 44°C. Pin Answer: 02= i Steel Tube (1) Pin MPa Copper Rod (2)
metal wires silicon frame cantilever doped piezoresiston silicon frame A fixed-free cantilever is made of single-crystal silicon. The resistor is made by diffusion doping, with a Gauge factor of 100. The length, width, and thickness of the cantilever are 100um, 20um, and 5um respectively. If a force F=10 uN is applied at the end of the cantilever as illustrated in the figure what would be the percentage change of resistance? The Young's modulus of silicon of the resistor is 130 GPa.
When stress is applied to a liquid over an application time tp the liquid needs a relaxation time tc to accordingly deform. Relaxation time tc is a physical property of liquids. The Deborah number is De= tdt, . The lower the Deborah number of a stress applied to a material the more.. : Select one: O The material behaves like a solid O The material behaves like visco-elastic O The material behaves like a liquid
augnol tofubbA 80 0.005W/mm S02 Figure 2) OF Figure 1) The femur bone is maintained and inclined 80 degrees with regard to the femur's resting position in the equilibrium state of an adducted femur, as shown in Figure 1. The pin and fixed joints, accordingly, are represented by Points A and B in Figure 2. Q001 W/mm 1-) Considering W on the loads distributed is equal to 637.65N, draw the Free body diagram of figure 2 and calculate the reaction forces at point A as well as point B. Construct the implant's shear and bending moment diagram by hand. Clearly demonstrate your work.
Annealing is a critical process in semiconductor manufacturing where silicon wafers get rapidly heated to get temperatures using powerful infrared heaters. Annealing helps to reduce defects in materials after implantation or deposition processes. a) You have been asked to design a temperature sensor an annealer with a range of up to 1500°C.Select a suitable thermocouple from the table below and give an explanation for your choice. 80 E 70 60 K 50 40 -C 30 20 10 0. 500 1000 1500 2000 2500 Temperature ("C) b) To record the temperature, you use a microcontroller with an ADC. The ADC is referenced to a 2.048V reference voltage source. To make use of the entire range of the ADC, what gain does the amplifier require for your chosen Thermocouple? c) You want to read the temperature with a resolution of 0.5°C. What is the minimum number of bits that your ADC requires? d) The thermocouple has a time constant, t, of 300ms. If the annealer heats from room temperature (20°C) to 820°C. What…
Q2/ semiconductor at T, has conductivity of 2.5 x 106 s/m. number of electrons of 3x 103 Numbers of holes 3x 103 ,charge of 1.602 x 10 -19 c, and at T2 has conductivity of 3.6 x 10 s/m , number of electrons of 4.5x 1014 , Numbers of holes 2x 102 ,charge of 1.602 x 10-19 c. Calculate the mobility of electrons and holes
A wire of radius 1 mm and conductivity 5x [10] ^7 S/m if an electric field of 5 mV/m is applied. Determine the current in the wire * 0.943 0.628 0.785 O 0.393
Q4. Two are applied to the pipe AB as shown. Knowing that the pipe has inner and outer diameters equal to 35 and 42 mm, respectively. Determine the normal and shear stresses at (a) point a, (b) point b.