Beam Bearing Plates and Column Base Plates 5.14-1 A W14 X 61 must support a concentrated service live load of 85 kips applied to the top flange. Assume that the load is at a distance of at least half the beam danth feom the support and design a bearing plate. Use F, = 50 ksi for the beam and F, = 36 ksi for the plate. a. Use LRFD. b. Use ASD.

Beam Bearing Plates and Column Base Plates 5.14-1 A W14 X 61 must support a concentrated service live load of 85 kips applied to the top flange. Assume that the load is at a distance of at least half the beam danth feom the support and design a bearing plate. Use F, = 50 ksi for the beam and F, = 36 ksi for the plate. a. Use LRFD. b. Use ASD.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.3P

See similar textbooks

Similar questions

Determine the maximum axial compressive service load that can be supported if the live load is twice as large as the dead load. Use AISC Equation E3-2 or E3-3. a. Use LRFD. b. Use ASD
4-47. The support consists of a solid red brass C83400 post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. A 0.25 m = 1 mm 60 mm 80 mm Prob. 4-47 -10 mm
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by ¾ inch boltas shown below. Use A36 steel with Fy=36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD
7.9-2 A structural tee bracket is attached to a column flange with six bolts as shown in Figure P7.9-2. All structural steel is A992. Check this connec- tion for compliance with the AISC Specification. Assume that the bearing strength is controlled by the bearing deformation strength of 2.4dtF. a. Use LRFD. b. Use ASD. D = 30 k L=70 k WWw.ma W12 X 65 34" diameter Group A bearing-type bolts with threads in shear
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
4-47. The support consists of a solid red brass C83400 copper post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Given the dimensions shown, determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. mm 0.25 m SOLUTION 60 mm -10 mm
Design the reinforcements of the given T beam below. bf=800mm bw=450mm tf=120mm d=600mm d'=80mm fc'=35MPa fy=350MPa USE NSCP 2015 A.Mu = 1300kN-m, As = B.Mu = 1600kN-m, As = mm2 _mm2, As' = mm2
De term ine the kin d and am ount of stress in e ach mem ber of the truss shown by the method of jo in ts in figure P 5-2 (page 76).- 1000lb 1000lb 1000lb 1000Ib 1000 Ib U. h = 20 ft 500lb 500 Ib L. L. RAV 6 pane ls at 10' - 6 ft RBy Note: 1. F o llo w strictly the lecture notes g iv en. Draw the FBD of e ach jo in t 2. Sum m a rize and tabu la te your answers. 3. Compu te the bar forces up to member U,L3 on ly because the truss lo a d in g is sym metric aland the bar forces of right sid e members are id en tic al w ith th e left s ide members. But you in c lu de th e rig ht sid e mem bers in have to the tabu la tion. 4. Show the com puta tio n ho w the leng th s were obta in ed. 5. Look for your own data in the table provided. 6. Copy the problem , data of problem and fig ure of the proble m TABULAT ION FOR SUMMAR Y OF COMPUTATION OF BAR FORCES METHOD OF JOINTS (PROBLEM P5-2 PAGE 76) Mem ber Identification Length Bar Forc e Туре of ft Ib force LOL1 10 3750 Tensio n L1L 2 10 Tension…
Design a column base plate for a W10 x 33 column supporting a service dead load of 20 kips and a service live load of 50 kips. The column is supported by a 12-inchx 12-inch concrete pier. Use A36 steel and f ,c= 3 ksi. a. Use LRFD. b. Use ASD