Please solve the below question.Regards BACTERIAL POPULATION A bacterial colonyis estimated to have a population of1512 + 1013 + 6t hours after the introduction of a toxin.P(1) =milliona. What is the population at the time the toxin isintroduced?b. When does the largest population occur? Whatis the largest population?Sketch the graph of the population curve. Whathappens to the population in the long run (ast→ +0)?c.

Given , Function of bacterial population with time after the introduction of a toxin

BACTERIAL POPULATION A bacterial colony is estimated to have a population of 151 + 10 13 + 6 t hours after the introduction of a toxin. a. What is the population at the time the toxin is P(1) million introduced? b. When does the largest population occur? What is the largest population? Sketch the graph of the population curve. What happens to the population in the long run (as 1- +0)? c.

BACTERIAL POPULATION A bacterial colony is estimated to have a population of 151 + 10 13 + 6 t hours after the introduction of a toxin. a. What is the population at the time the toxin is P(1) million introduced? b. When does the largest population occur? What is the largest population? Sketch the graph of the population curve. What happens to the population in the long run (as 1- +0)? c.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute a little more by taking the integralinii) terms up to the 5th order ii) taking the terms up to the 7th order
Find the circumference and the area of a circle with diameter 10 cm. Write your answers in terms of t, and be sure to include the correct units in your answers. (a) Circumference: 10 cm (b) Area:
Solid steel wire (2 meters) contains a musical instrument (0.3 mm). When the wire is under tension (90N), how does its length change?
(Use the following figure to answer questions b, c and d) T du dy Liquid A Liquid B b. What is the type of the two liquids? c. Explain how the shear force applied to each liquid affects its viscosity. d. Which liquid has higher apparent viscosity? Explain your answer.
Please write the final answer with unit 3.Length and diameter of a bearing are equal (d=L). This bearing should be able to withstand the allowable support force of 80 N. Allowable support tension is 20 N/cm?. Determine the length of bearing.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
i) Find the property that provides the change in size of the material, if the material is subjected to temperature change and explain that property with unit. ii) Water of 1.6 liters is heated to a maximum temperature of 116 °C from room temperature to prepare Arabic coffee for a family using the following data. -- (2.5 Marks) - Heat energy of 623 kJ is supplied to the water - Specific heat capacity of water is 4.2 kJ/kg K - Density of water as 1000.5 kg/m3 Determine the room temperature. a) Mass of water (in kg) b) Room temperature (in °C
A gas filled in a piston-cylinder arrangement as shown in Figure 1 has a volume of 0.09 m³ at its initial equilibrium state. The gas is slowly heated through the bottom of the cylinder that allowed for the gas to expand at constant-pressure of 2095 kPa to a volume of 1.23 m°. The change in internal energy of the gas is 0.24 kJ. Ignoring the friction between the piston and the cylinder and assuming the atmospheric pressure any value from 90 to 110 kPa, of (a) Calculate the mass of the piston if the area of the piston is 0.047 m2 (b) For the gas as a system, evaluate work and heat transfer, each in kJ (c) For the piston as a system, evaluate work and change in potential energy, each in kJ Piston Gas