Answered: A thin cylinder have inner radius 175…

A thin cylinder have inner radius 175 mm and thickness 4 mm subjected to an internal pressure of 3MPa. Determine average circumferential stress?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: thin cylinder have inner radius 210 mm and thi mm subjected to an internal pressure of 4 MPa…

A: Radius (r) of cylinder=210mm Thickness (t)=5mm Internal pressure (p)=4MPa To find circumferential…

Q: 4. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN.…

A: Given data in question Inside diameter Load Stress To find out Outside diameter

Q: For an allowable stress of 15 000 psi, what is the maximum design pressure permitted for r/t=5,…

A: Allowable Stress S = 15000psi r/t = 5 r = inside radius t = required thickness To determine Maximum…

Q: Determine average circumferential stress?

A: Given data, A thin cylinder having following data observed is; Radius, r= 210 mm Thickness, t= 5…

Q: Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 40*10 deep…

Q: A thin cylinder have inner radius 210 mm and thickness 5 mm subjected to an internal pressure of 4…

Q: A fire extinguisher tank is designed for an internal pressure of 986 psi. The tank has an outer…

Q: circumferential stress?

A: Given data, Inner radius,r=725 mminternal pressure,p=6 MPathickness,t=5 mmDetermine average…

Q: A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown…

A: Given data:Internal pressure, p=510 KPa Thickness of the wall, t=20 mm or 0.02 mDiameter of the…

Q: Compute the principal stress. Determine maximum shear stress

A: Given data : σX=-10000 psiσY=-13000 psiζXY=7000 psi

Q: 12 m high is completely filled with

Q: A hollow circular tube is subjected to a tension force of 30 KN, a tensile stress of 20 MPa was…

A: Intensity of Tensile force acting of circular hollow tube, tensile stress, outer diameter have been…

Q: A thin cylinder have inner radius 235 mm and thicknes 6 mm subjected to an internal pressure of 5…

A: Given data : The value of internal pressure p=5 MPa The value of thickness of thin cylinder t=6 mm…

Q: A fire extinguisher tank is designed for an internal pressure of 899 psi. The tank has an outer…

A: Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses…

Q: Determine the design moment strength pM, of the T-beam in the slab shown. The span length of the…

A: Given Data -

Q: maximum stress in the plate.

A: Given data, Uniform uniaxial tension of, P=50 MpaD= 2cm width,b= 5 cmFind maximum shear stress in…

Q: 90mm 60mm 90mm 90mm 60mm 90mm Since there is a pressure force P at point A, a tensile force of 2P at…

A: Given Data: pressure force = P at A pressure force = 4P at C pressure force = 2P at B

Q: An upright cylindrical water tank having a diameter of 3 meters and a height of 6 meters is to be…

Q: AN 8 MM THICK CYLINDRICAL STEEL TANK HAS AN OUTSIDE DIAMETER OF 600 MM AND A LENGTH OF 3 M. (a) WHEN…

A: Given Thickness 8mm Diameter 600mm Assume unit weight of water 10kn/m^3

Q: A thin cylinder have inner radius 235 mm and thickness 6 mm subjected to an internal pressure of 5…

Q: Situation 3: 200.02 kN 75.05 mm 50.05 mm 15.05 deg 200.02 kN 1. Tensile stress at section A-A 2.…

Q: k 3 m in diamter and 8 m tall has a wall thickness of 13 mm. The tank is filled with water. (Use…

A: Diameter ( D )= 3 m Depth ( h ) = 8 m Wall thickness (t) = 13 mm

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the %3D flexural…

A: To determine the flexural stress at a given location for given cross-sectional information and…

Q: The flow of water (mass density - 1000 kg/m³) and kinematic viscosity = 10-6 m² /sec, a compressible…

A: Given: Mass density=1000 kg/m3,Kinetic viscosity, v=10-6 m2/s,Stress=600 N/m2 It is needed to find…

Q: Compute the combined stress. P = 11 KN 1.5m 16KN P = 11 kN 3m L = 6m 1.5m 16KN b=50mm d=100mm

Q: 40 35 60 -60 35 140 MPa

Q: A thin cylinder have inner radius 210 mm and thickness 5 mm subjected to an internal pressure of 4…

Q: 1. Determine the normal stress caused by the load in the drawing below. The cylinder is hollow with…

A: Given:- The outside radius of the hollow cylinder = 6 in The inside radius of the hollow cylinder =…

Q: Q6. Hoop stress (0₁) in a thin-walled pressure vessel is 40 MPa. What is the maximum 'in-plane'…

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: QUESTION 6 A 12 inch Schedule 80 natural gas pipe running along the sea-bed at a depth of 7522 ft…

Q: 04) From the figure below, calculate the increment stress (Ao) at depth(z=1 )meter under the point B…

A: To find :- The increase in stress due to two point load applied at points A and B 5 m apart at Z = 1…

Q: 4. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN.…

A: Given, Inside diameter = 100 mm Allowable stress = 120 MPa Tensile load = 400 kN Outside diameter =?

Q: Determine average circumferential stress?

A: Given, Radius,r= 235 mmthickness,t= 6 mmpressure,p= 5 MPaDetermine average circumferential stress ?

Q: Challenge Problem 3) A 1m long copper bar is placed between two rigid, unyielding walls with only…

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A: given data A cylindrical pressure vessel has thickness, t= 20 mm diameter, d= 15 in. length, l= 6.6…

Q: ase value of Q for the pipe. ertical shear stress in the

Q: inclined at 30° to the known directions of the Q.10 In a stressed member , *0 zetio u = 0.3.…

Q: A thin cylinder have inner radius 210 mm and thickness 5 mm subjected to an internal pressure of 4…

A: Given- Inner radius r= 210 mm, Thickness t =5mm, Internal pressure p=4 MPa,

Q: An aluminum alloy pipe with an outside diameter of 3.5 in. and a wall thickness of 2/16 in.…

Q: A fire extinguisher tank is designed for an internal pressure of 874 psi. The tank has an outer…

A: Given data, Intenal pressure P = 874 psi Diameter d = 4.5 in Thickness t = 0.08 in NOTE:- As per our…

Q: 10 mm diam 5 mm diam 6 mm diam 500 N 900 N 800N C 400N

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

A thin cylinder have inner radius 175 mm and thickness
4 mm subjected to an internal pressure of 3MPa.
Determine average circumferential stress

Expert Solution

Step 1

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question-fluid. Water is flowing through a pipe of 40cm diameter with friction factor equal to 0.06 At a distance of 5cm from the axis, the shear stress was found to be 120Pa. What is the shear stress at the pipe wall Pa
220 mm 180 mm Screws 40 mm 40 mm 140 mm 40 mm Calculate thickness at the depth of maximum horizontal shear stress.
Determine the Adjusted Unit Compressive with dimension of ends with length of is 9.56 MPa. E= Fixed Fixed Stress for a rectangular column 200 mm x 200 mm and fixed support at both 4.5 meters. If the Allowable compressive stress 7310 MPa PI 4.50 m 200 mm 200 mm Column Section
Solution please,
Determine total stress and effective stress at point A
A thin cylinder have inner radius 210 mm and thickness 5 mm subjected to an internal pressure of 4 MPa. Determine average circumferential stress?
The pressure of sulfur dioxide (SO2) is 2.07 x 104 Pa. There are 498 moles of this gas in a volume of 44.5 m3. Find the translational rms speed of the sulfur dioxide molecules. Number i 181 Units m/s
A thin cylinder of inner radius 725 mm and thickness 5mm subjected to an internal pressure of 6Mpa. Find average circumferential stress?
A thin cylinder of inner radius 725 mm and thickness 5mm subjected to an internal pressure of 6Mpa. Find average circumferential stress?
1
Provide complete solution with FBD and explanation.
Problem 1: If the parts of the shaft below are a 1" diameter solid steel rod and a 2" OD diameter steel pipe with a 0.25" wall thickness, what is the torsional stress in each section of the shaft? В A 6 in. 15 lb 8 in./ 15 lb