(b) Figure 3 shows a pump with 80% efficiency (n.) delivers 50 Liter/s of water at 20°C from tank 1 to tank 2. The pipeline has 150 mm diameter with a length of 200 m made of galvanised steel. Evaluate the input power to an electric motor of 90% (nm) efficiency that connected to the pump. The globe valve used is % wide open. 2 100 m GLOBE VALVE PRESSURE GAUGE MOTOR PUMP

(b) Figure 3 shows a pump with 80% efficiency (n.) delivers 50 Liter/s of water at 20°C from tank 1 to tank 2. The pipeline has 150 mm diameter with a length of 200 m made of galvanised steel. Evaluate the input power to an electric motor of 90% (nm) efficiency that connected to the pump. The globe valve used is % wide open. 2 100 m GLOBE VALVE PRESSURE GAUGE MOTOR PUMP

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1) Figure Ql shows piping system with pump to drive the oil upward from A (P=PA kPa) to B (P=180 kPa) at a mass flow rate of 3 kg/s. Determine type of flow and calculate required pump power. Given data: oil density and viscosity are 891 kg/m³ and 0.29 N.s/m² respectively. Use Hagen Poiseulli equation for loss: he128µQL/(xpgD“) and Power=Qpghr; Triangle geometry: a²=b²+c² Dripe = 3 mm 15 m Pump 20 m Figure O1
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of thestroke volume. At the beginning of compression stroke the pressure of air is 0.99 barWhen the piston has travelled 260 m from the begining of the compression stroke thedelivery valves open and delivers air at 4 bar. Find the value of "n", iif the compressionfollows the law PVn = CA. 1.37B. 1.39C. 1.28D. 126
asap
4. A pump is used for the pumping of water from Tank A into Tank B in which the height difference between the surface levels of water is 20 m. The pipe diameter is 400 mm and the pipe length is 2500 m, the coefficient of friction is f 0.0025 and the pump works at a speed of 700 rpm. The characteristics of the pump are shown in Table 4 below You are required to: (a) (10 points) Intepret pump characteristic and system characteristic ina graph. (b) (10 points) Calculate the input and output power at the operating point. 0.1 0.2 0.3 0.35 0.4 0.5 15 17 18 16 14 O30 60 SI83.80 45 H. (m) 11 Table 4: Data of the pump from the Manufacturer
A large centrifugal pump has a 254 mm diameter inlet and a 127 mm diameter outlet pipe. Themeasured flow rate is 51.6 Liter per second of cold water. The measured inlet pressure is 127 mmHg above atmospheric and discharge pressure measured at a point 1.22 m above the pump outletis 212 kPa absolute. The pump input is 10 Hp. Find the pump efficiency
Q.2 A centrifugal pump is required to pump water to an open water tank situated 4 km away from the location of the pump through a pipe f diameter 0.2 m having Darcy's frřiction factor of 0.01. The average speed of waterinthe pipe is 2 m/s. If it is to maintain a constant heac of 5 m in the tank, neglecting other minor losses, the absolute discharge pressure at the pump exit is (a) 0.449 bar (c) 44.911 bar dund (b) 5.503 bar (d) 55.203 bar
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) thepump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A centrifugal pump delivers 227 m³/hr of water from a source 4 meters below the pump centre line to a pressure tank whose pressure is 2.8 kg/cm² . Friction loss estimates are 2 meters in the suction line and 1 metre in the discharge line. The diameter of the suction pipe is 250 mm and the discharge pipe is 200 mm. Find: a. The water horsepower b. The kW rating of the driving motor if the pump efficiency is 70%
A single-stage centrifugal pump having a suction pipe 254 mm in diameter anda discharge pipe diameter of 5 inches is being tested and found out to discharge 48 lps ofwater. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and adischarge gage reads 150 kPa at a distance 100 cm above the point where the inletpressure was measured. If the kW rating of the driving motor is 12 kW, calculate a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate,head, and power developed if the pump speed was increased to 3600 rpm? Assumeconstant efficiency. c) Determine the pump type.
A large container filled with water and uncovered for use in fighting fires in an ethylene production plant. Water from this tank is pumped into the nozzle when needed use. This fire suppression system is designed to be able to transmit 1890 L/min of water at a pressure of 15 bar (relative pressure). If we ignore the difference in height between the water level in the tank and pump, there is no change in diameter of pipe and nozzle, pump efficiency is 70%. Ask how much work (hp) is required to the pump to achieve the desired pressure and flow would like?
Sketch the energy grade line (EGL) and hydraulic grade line (HGL) for the pipeline below.
1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)