AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. Y X+Y Properties of W 12 x 65 A 12323 mm? Tx 134.11 mm ry- 76.71 mm F,- 248 MPa Determine the allowable compressive strength (kN).

AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. Y X+Y Properties of W 12 x 65 A 12323 mm? Tx 134.11 mm ry- 76.71 mm F,- 248 MPa Determine the allowable compressive strength (kN).

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.7.3P

See similar textbooks

Similar questions

Problem 2 Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing stress due to rivets is 140 Mpa • Thickness of the member is 5 mm • Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 N 120 N 200 N 4 Pands 4m - 16 m
Design the reinforcements of the given T beam below. bf=800mm bw=450mm tf=120mm d=600mm d'=80mm fc'=35MPa fy=350MPa USE NSCP 2015 A.Mu = 1300kN-m, As = B.Mu = 1600kN-m, As = mm2 _mm2, As' = mm2
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN
A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa. Determine the design (LRFD) tensile strength of the tension member in kN. Neglect block shear. H G P P D B F C A E
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
The wall bracket show below carries a load of P Kip. the allowable tensile in the eye bar is 20 ksi, and the allowable shear stress in the pin is 12 ksi. Select: a) The diameter of the eye bard b) the diameter of the pin at A which is double shear c) the diameter of the pin at B which is single One eye-bar 6 ft P kip 4 ft
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
A column is built up from four (4)- 125 x 125 x 18 angle shapes as shown. The plates are not continuous but are spaced at intervals along the column length and function to maintain the separation of the angles. They do not contribute to the cross-sectional properties. The effective length is 4 m. Compute the allowable design compressive strength based on flexural buckling. E= 250 MPa. Use ASD. k 375 mm 125mm, HPlate 125mm 4 - 4 125 × 125× l8 section 下好业

A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa. Determine the design (LRFD) tensile strength of the tension member in kN. Neglect block shear. H FO E. • D A В
A built-up section shown, 30 feet long, is fixed at both ends and braced in the weak direction at the midheight. A992 steel is used. Determine the following: 11. Ix 12. Ky 13. effective slenderness ratio 14. Fe 15. LRFD design strength 16. ASD allowable strength 18 4 W10 × 49 A 14.4 in² bf 10 in d. 10 in tw 0.340 in tf 0.560 in Ix= 272 in¹ Iy=93 4in¹ W10×54 A 15-3 in² bf 10 in d = 10 lin tw0-370 in tf 0.615 in Ix= 303 in 4 Ty = 103 in 1
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co