Auniform rod s attached to a wall by a hinge at ts base. The rod has a mass of 1.5 vg, a lenoth of 1.8 m, is at an angle of 21 above the horizontal, and is held in place by a horizontal cord attachedto the other end of the rod and bolted to the wall above the base of the rod.(a) Determine the tension in the cord.(b) Determine the horizontal and vertical components of the force exerted on the red by the hinge.

Given, Mass =1.5 kg Length = 1.8 m Angle = 21∘

Auniform rod is attached to a wall by a hinge at ts base. The rod has a mass of 1.5kg, a length of 18 m is at an angle of 21 above the horizontal, and is held in place by a horizontal cord attached to the other end of the rod and boited to the wall above the base of the rod. (a) Determine the tension in the cord. 0) Determine the horizontal and vertical components of the force exerted on the rod by the hinge

Auniform rod is attached to a wall by a hinge at ts base. The rod has a mass of 1.5kg, a length of 18 m is at an angle of 21 above the horizontal, and is held in place by a horizontal cord attached to the other end of the rod and boited to the wall above the base of the rod. (a) Determine the tension in the cord. 0) Determine the horizontal and vertical components of the force exerted on the rod by the hinge

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 41PQ: In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy...

See similar textbooks

Similar questions

length. Two wires A and B are of the same Their diameters are in the ratio 1: 2 and the Young's modulii are in ratio 2:1. If they are pulled by the same force, then elongations will be in ratio (a) (c) 4:1 1:2 (b) (d) 1:4 2:1
10° A V60° B If the maximum tension force the cable AB could carry is 1500N before breaking, and the maximum compressive force the pole AC could carry is 2200 N before buckling, what is the maximum value of P in Newtons
The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 8.6 kN. Determine the required tension Tin cable AC such that the net effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force. Assume a = 45m, b = 56 m, c= 26 m, and d=32 m Answers: i Ri KN kN
Determine the normal force N inside each bar Sa function of the external force P 1.5 m 2 m Probs. 1-40/41/42
A mass of 1400 kg rests on an oak beam. The beam rests on 200-mm diameter rollers. Assuming the coefficient of rolling resistance between the beam and the rollers to be 0.90 mm, what horizontal force is necessary- to move the load on a level surface?
Two wires A and B are of the same length. Their diameters are in the ratio 1:2 and the Young's modulii are in ratio 2 : 1. If they are pulled by the same force, then elongations will be in ratio
A force stretches a wire by 1.4 mm A Subr
The Tethered Satellite in shown has a mass of 525 kg and is at the end of a 20.0 km long, 2.50 mm diameter cable with the tensile strength of steel. (a) How much does the cable stretch if a 100 N force is exerted to pull the satellite in? (Assume the satellite and shuttle are at the same altitudeabove the Earth.) (b) What is the effective force constant of the cable? (c) How much energy is stored in it when stretched by the 100 N force?
What type of stress are you applying when you press on the ends of a wooden rod? When you pull on its ends?
Two forces of magnitude TA= 7607 lb and TB= 14617 lb are applied as shown to a welded connection. Knowing that the connection is in equilibrium and angle X is 48°, determine the magnitude of TC (lb).
How far from Q 2 must Q 3 be located so that the forces on Q 2 are at equilibrium ? ( Ans: 16.5 cm)
The light a verticaA boom AB TS attached to a Wall by a bail qud socket int ar A qndsupported nt at A qnd Suppurted by two cables at B. A force Pis applied bteo Cabtes at B where P = I4 -1) KN. Note that the reactian force at A acts along the boom becauuse it is a two - force member iCalculale the agndude magntude 177eaction force at AiA KN m= meters 4m 6o 6 m A dDetermine the magnitude of the origin CPoint O) in Nm the momenmt of P about b) Determine the magnitude of the moment of P about the X-ascis in Nm 3m. C.