Ast A32 A A X, A x Asx Asx Ase A2 1-find a) Input and Output nodes. b) . Forward paths. c) Feedback paths. d) Self loop e) . Determine the loop gains of the feedback loops. f) Determine the path gains of the forward paths. 2- Apply Mason's Rule to calculate the transfer function of the system represented by following Signal Flow Graph

Ast A32 A A X, A x Asx Asx Ase A2 1-find a) Input and Output nodes. b) . Forward paths. c) Feedback paths. d) Self loop e) . Determine the loop gains of the feedback loops. f) Determine the path gains of the forward paths. 2- Apply Mason's Rule to calculate the transfer function of the system represented by following Signal Flow Graph

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Construct the Bode plots of the following transfer functions. Indicate Gain Margin and Phase Margin of the systems. a) b) 8 s(1.25s + 1)(s+2) 1.6 (s+0.4)(s+0.8) (s + 1)
2- Using Matlab, what are the step response curves of the closed-loop system, as shown in fig.1. the feedback represents the second-order dynamic system. (fill in the following table) For=0.4 Wn 1 3 6 9 10 R(S) 0.1 0.3 0.6 0.9 1 For w 5 rad/sec 3 Settling time Peak response 2 Wn s(s+23wn) Settling time Peak response C(s) Discuss the follow Which parameters or w occur on the rise time of the response? Which parameter increases the speed of response? Which parameters can be decreases the response amplitude? Which parameter decreases the steady error state? fig.2
7- Name the functions used, for multiplication of two polynomials p1, and p2 in MATLAB. a) convolution (p1, p2) b) multiply(p1, p2) c) conv(p1, p2) d) mult (p1, p2) 8- The Transfer Function of an L.T.I. system is entered as: a) trans_func(num, den) b) transferfunction (num, den) c) tf (num, den ) d) TF(num, den ) 9. What is the nature of the arrangement of the coefficients to store the expression y = 3s5+ s² + 6 in MATLAB? a) y=[3,0,0,1,0,6] b) y=[3,1,6] c) y=[3;0;0;1;0;6] d) y=[6,0,1,0,0,3] 10. To enter the transfer functions G(s): 2 to Matlah command use
For the system represented by the following block diagram, Find a) The Closed-loop Transfer function. b) Characteristic equation. c) Type and Order of the system. c) Time-domain Specifications ( Delay Time, Peak Time, Rise Time, Settling time, and Percentage overshoot). R(s) C(s) G(s) H(s) Where G(s) and H(s) are given as : 324 G(s) = s(s+6) H(S) : 1
X(s) from the following block diagram. F(s) Obtain the transfer function F(s) + X(s) 9. 5 9 A) s - 6 9. B) s + 14 9. C) s+ 4 s + 4 D) s + 6
Determine the state-space representation: Let: x₁ = y₁, x₂ = y₁, Xxz = y₂₁ xy = y₂ Vilt) FIE) ki m B₁ mi M₂ 2 Yalt) K₂ B2
1) Consider the system below: Vehicle Controller Steering dynamics Desired Actual bearing angle bearing angle 50 1 K s2 + 10s + 50 s(s + 5) Figure 1: Simplified Block Diagram of a Self-Guiding Vehicle's Bearing Angle Control. • Find a K value that the system has minimum rise time and minimum overshoot. Let us call this proportional gain as Kopt Show each step while finding Kopt- Show the necessary graphical solutions. Simulate the system response with 3 different K values. (Kopt and two other K values close to Kopt) Show the system response (actual bearing angle) in a single graph for different K values. • Comment on the results.
Required information Use the following transfer functions to find the steady-state response yss() to the given input function f(t). NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. T(-) Y(s) F(s) s(e) 10 b. = 9 sin 2t s²(s+1) ' The steady-state response for the given function is yss() = | sin(2t + 2.0344).
#3) a) Show that the below given system has the following representation where u=x. 1 cl %3D b) Plot the impulse response of the system for m=10, c=3, k=5,1,=l½/2=l3/2=1. c) Find the transfer functions, poles and zeros of the system. #4) a) Show that the state space respresentation of the cartesian elbow manipulator is as given below. b) Assuming unit values for all constants, plot the q, and q, angles for 5 seconds for the nonzero initial conditions (q,lo= (q;)o=30°. c) Find the transfer functions, poles and zeros of the system.
As the control engineer on a project you are given the following information: a) The free body diagram representation of a mechanical system with the various values for the damper, spring and mass. The transfer function for the system is also provided. 28 N/m -x(1) 1 G(s): - f(1) s? +s+5.6 5 kg 5 N-s/m b) The step response plot for the system. Step Response 0.14 0.12 0.1 0.08 0.06 0.04 0.02 10 Time (sec) Your task is to analyse the system and to confirm that the diagram is for the system in a) i.e. calculate all time responses and compare your answers with the data in the graph. apnadu
Consider the following Initial Value Problem (IVP) dy /at = -t * sin (y); y(t = 0) =1 Solve for y(t=0.5) using a) Forward Euler method with At = 0.25. (Solve by hand) Develop a Matlab script that solves for y (t = 5) using Forward Euler method. Use the time step levels given below and plot t vs y in the same plot. Include the plot with the right format (axis labels, legends, ...) in your solution sheet and include your Matlab script in the solution as well. i) At = 0.25 ii) At = 0.125 b) Backward Euler method with At = 0.25 (Solve by hand)
Feedback & Control Systems State-Space Representation Write the state-space representation of the system below. Let the output of the mechanical system is x3 (t). 1 N-s/m x₁ (t) M3 = 1kg 1 N/m М1 -0000 1kg > X3 (t) 1 N-s/m 1 N/m oooo x₂ (t) M₂ 1kg 4 1 N-s/m² -1 N-s/m →f(t)