Assuming the following velocity distribution in a circular pipe, 1/7 Umax (1-4) ¹7 U = Umax where Umax = maximum velocity, R = radius of pipe, u = velocity at a radius r from the centre of pipe, calculate : (1) The ratio of the mean and the maximum velocity (1) The radius at which the actual velocity equals the mean velocity.

Assuming the following velocity distribution in a circular pipe, 1/7 Umax (1-4) ¹7 U = Umax where Umax = maximum velocity, R = radius of pipe, u = velocity at a radius r from the centre of pipe, calculate : (1) The ratio of the mean and the maximum velocity (1) The radius at which the actual velocity equals the mean velocity.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(c) Venturi-type flowmeter shown in Figure 5 is used to obtain the flowrate of oil inside a conduit. The diameter of the venturi, d is one third of the pipe diameter, D. The pipe diameter D is 6 cm, pressure difference reading AP, is 25 kPa, discharge coefficient Ca, is 0.98, Bis the ratio of venturi diameter to pipe diameter and oil specific gravity, SG is 0.95. i) Calculate the volume flowrate of oil inside the conduit. ii) Determine the mass flowrate of oil inside the conduit. iii) Explain why the discharge coefficient Ca, for the ventury meter is higher compared to the nozzle meter. 2(P – P.) V. ventury AP oil d Figure 5
Consider the problem of draining a hemispherical tank of radius H* feet that is full of water and has a circular drain hole of radius 3 inches at the bottom. How long will it take for the tank to empty? dv When the change volume is = -kA/2gh(t) A is the constant cross sectional area of the opening; and k is a constant determined by the viscosity of the fluid dh dt H H-h dV 1 dt dt ar² Note: Draining a hemispherical tank. Take H* as a last two digits of your ICEM ID, if last two digits less than 10 take H= 18 feet
A two-dimensional flow field for a liquid is defined by V[(z+2y³)i + (2x-3y)j m/s, where z and y are in meters Part A Determine the magnitude of the velocity of a particle located at (-2 m, 1.2 m) Express your answer to three significant figures and include the appropriate units. V= Submit Part B Request Answer Determine the direction of the velocity of a particle located at (-2 m. 1.2 m). Measure the angle counterclockwise from the positive z axis. Express your answer in degrees to three significant figures. 0- Submit Request Answer
For the Venturi meter and manometer installation shown, derive an expression relating the volume rate of flow with the manometer reading. Denote p as the density of fluid and pm as the density of the fluid in the manometer. Ans: Q = A₂[ {(2gR) (pm/ p-1)}/(1- (D2/D1)^4) ] ^1/2 Datum D1 z1 z2 R ↑
16. Fluid Flow through a Compression Chamber A compressible gas flows into and out of a compression chamber as shown in Figure 9. Vin = 10 m/s Ain = 0.1 m² Pin = 3.0 kg m-3 (a) Bsys = 0 (b) bsys = dB sys dt Control Surface For the system given, which of the following statement(s) are true based on the conti- nuity equation? Be certain to justify your answer quantitatively. 0 Control Volume Figure 9: Schematic of compression chamber. (c) #0 (d) Σsbpv · A = 0 (e) & Spdv = 0 Vout = 5 m/s Aout = 0.2 m² Pout = 2.0 kg m-3 Answer(s): # 0; dB sys dt
Q2) The velocity distribution for turbulent flow in pipes can be represented by the following equation: u- Ū y = 5.75.log10+3.75 in which: %3D u. u is the local velocity, U is the average velocity, u, is shear velocity, y is the distance from pipe wall, and R is the radius of the pipe. Show that: -2.03 f log10 Итах u %3D
The velocity profile of a liquid flowing through the pipe is approximated by the truncated conical distribution as shown in (Figure 1). Suppose that V = 4 ft/s. Hint: The volume of a cone is V=1/r²h. 0.3 ft 0.6 ft 0.3 ft DE V Determine the average velocity of the flow. Express your answer to three significant figures and include the appropriate units.
c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit. The diameter of the orice, d is one third of the pipe diameter, D with pressure difference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is 0.60, Bis the ratio of orifice diameter to pipe diameter and Oilspedific gravity, SG is 0.95. If the h is 7 cm, i. Calculațe the vollime flowrate of oil inside the conduit. ii. Determine the mass flowrate of oil inside the conduit. iii. Explain why the discharge coefficient Ca, for the orifice meter is higher compared to the venturi and nozzle meters. D=6 cm d Figure 4
4- Consider the system shown in the figure. If a change of P kPa in the pressure of air causes the brine- mercury interface in the right column to drop by d mm in the brine level in the right column while the pressure in the brine pipe remains constant, determine the ratio of A₂/A₁. P (kPa) d (mm) 6 Sum of last 2 digits of 35 YorkU ID# ending with 0, 2, 4, 6, 8 Sum of last 2 digits of 45 YorkU ID# ending with 1, 3,5,7,9 7 Area, A₁. Air Water Mercury SG = 13.56 Brine pipe SG = 1.1 Area, A₂
Part B Taking in your consideration the head losses accumulated by the fluid when flowing in the pipeline: - Now determine water velocity at the pipeline exit as a function of time. Note that friction factor f can be calculated by using Blasius formula (f = (100 * Re )-0.25 ) if Reynolds number is less than 105
Answer is 1,614.71. No other answer thanks. The projectile shown is launched at Vo = 92 m/s at 57° above the horizontal. The surface on which it lands is described by the equation shown. Determine the abscissa of the point of impact.
Part A If the plates are spaced 200 mm apart, determine the time t′ for the particle to travel from one plate to the other. When t=t′/2 the particle is at s = 100 mm Express your answer using three significant figures and include the appropriate units. Part B Determine the maximum velocity Vmax (3 sig figs and appropriate units)