Assuming that a 4-bit ADC accepts analog input ranging from 0 to 6 volts, solve the following: a) The number of quantization levels is b) The step size of the quantizer is c) For a signal level of 3.25V, the quantized value is and the binary code of that quantized value is volt volts

Q: The modulation techniques used to convert analog signal into digital signal are a. Pulse code…

A: The correct option along with the explanation is provided in the following section.

Q: an input signal ranges from 20–40 A (microamps), with an output signal ranging from .5–1.5 mA…

A:

Q: Define the quantization error and then show how it is changing when using an A/D converter with…

A: When an analogue signal is converted to a digital signal by an analog-to-digital converter (ADC), a…

Q: assuma VA=15, perform large signal model and small sginal analysis, drow the equivelnt small signal…

A:

Q: Q4: Draw the constellation diagram of 2*4 QAM signal then show the output amplitudes and phases of…

A:

Q: 6.q1.t2

A: The resolution of a D/A converter is the smallest change in voltage that can be produced by a 1 bit…

Q: "| vo%! Mux, is a device that can be use to 1 point select one from many many from one parallel…

A:

Q: Consider a 9.4-bit ADC and full scale voltage measurement range of (-41V to 41V).The Resolution will…

A: Resolution is given by  R = Dynamic Range / total number of steps  Resolution = Dynamic Range /…

Q: Draw the waveforms of FSK if the modulating data signal is 1 0 0 1 1 0 1 (Draw the modulating data…

A:

Q: The output from a sensor ranges from a minimum of 10 mV to a maximum of 200 mV as the measurand…

A: An instrumentation amplifier allows an engineer to adjust the gain of an amplifier circuit without…

Q: ..... .. .. ... .... ... In PCM, the first step after PAM, is coding of the analog pulses. Select…

A: We need to tell about the PCM .

Q: Addressing mode H.W.1 1. What is the addressing mode of each of the following instructions: a-mov…

A: According to the given question, it is required to determine what type of addressing mode is given…

Q: 2. A thermal couple measures a temperature range between 0°C to 500°C. It is required that the…

A: According to question: Resolution = 0.50C

Q: 1. Derive a Boolean expression for the following digital circuit -

A: Given digital circuit,

Q: Question 9 Piezoelectric devices are examples of ..components. Select one: O a. o b. O C. O d. O e.…

A:

Q: t Rrom the outPut signal för half and l wave rectifer. calculate the Peak.ruot mean squgre and de…

A:

Q: Q2) Convert to decimal number: 1) The hexadecimal number (FD45) 2) The octal number (7024)

A:

Q: we can see the following signal at which point of the modulator? 6 A Modulating signal D Carrier -…

A:

Q: Write the fragment 'C' code to configure the 12 bit analogue to digital convertor in a MSP430…

A: It is asked to write the fragment 'C' code to configure the 12 bit analogue to digital convertor in…

Q: analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz.  The…

A: We need to find out the number bits per sample for quantization error .

Q: 6. Draw the circuit diagram and find the value of 'X' bit for a digital to analog conver, if Vout…

A: According to the question we have to draw the circuit diagram and find the value of 'X' bit for a…

Q: - Design a flash ADC with input voltage range [ igital output for a 2.5 V input signal?

A:

Q: n . when input change, may affect the output Morre model Mealy model O

A:

Q: For 4-bit DAC Binary Weighted Resistor Method, if the Vref = 20V, and R = 5 Kohm, what is the output…

A: In this question we need to find a output current for the sequence 1001

Q: (1-20) In a PCM system, SNR is to be held to minimum of 40dB. Determine the number of required…

A: To determine the number of quantizing levels \( L \) required to achieve a minimum…

Q: The lowest difference between original sample voltage and the voltage at the actual quantized level…

A: Option B is correct. The lowest difference between original sample voltage and the actual quantized…

Q: Q. ) What are the frequencies F1, F2, F3 10MHZ is applied? after each stage if an input clock of…

A: Counter is a  sequential circuit made up of flip flop which are connected to count the pulses . It…

Q: Instant Binary data 1 101000 101010 3 101101 Table 1

A: It is given that: Refrence Voltage=Vref=100 VBits=n=6 The given table is shown below:

Q: can you help me at least up to paragraph 3 or 4, please?

A: The objective of the question is to design a decadic counter that operates in up/down mode using…

Q: The modulation techniques used to convert analog signal into digital signal are

A: The correct option along with the explanation is provided in the following section.

Q: The modulation techniques used to convert analog signal into digital signal are a. Pulse code…

A: The correct option along with the explanation is provided in the following section.

Q: Design circuit BCD-8421 to 7 segment Decoder using Gate circuit. combination

A: BCD to 7-segment decoder

Q: Consider an analog to digital (ADC) convert that has a resolution of 8 bits, and a reference voltage…

A: So we have to find step size  Output voltage for the given input  And quantization noise

Q: The attenuation in the pass band or stop band is called a. Cutoff Frequency b. Ripple c. Band…

A:

Q: QZ. Design a combinational circuit with the help of appropriate encoder for the conversion of…

A: Decimal to binary conversion using appropriate encoder: (0-7 numbers)

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.