Assignment#5 Refer to Electronic Devices, Floyd chapters 15, 16 and 17 Part A: Filters 1. 3. 2. The term pole in filter terminology refers to (a) a high-gain op-amp (c) a single RC circuit (b) one complete active filter (d) the feedback circuit A band-pass response has (a) two critical frequencies (c) a flat curve in the passband (b) one critical frequency (d) a wide bandwidth When a low-pass and a high-pass filter are cascaded to get a band-pass filter, the critic frequency of the low-pass filter must be (a) equal to the critical frequency of the high-pass filter (b) less than the critical frequency of the high-pass filter (c) greater than the critical frequency of the high-pass filter When the gain of a filter is minimum at its center frequency, it is

Assignment#5 Refer to Electronic Devices, Floyd chapters 15, 16 and 17 Part A: Filters 1. 3. 2. The term pole in filter terminology refers to (a) a high-gain op-amp (c) a single RC circuit (b) one complete active filter (d) the feedback circuit A band-pass response has (a) two critical frequencies (c) a flat curve in the passband (b) one critical frequency (d) a wide bandwidth When a low-pass and a high-pass filter are cascaded to get a band-pass filter, the critic frequency of the low-pass filter must be (a) equal to the critical frequency of the high-pass filter (b) less than the critical frequency of the high-pass filter (c) greater than the critical frequency of the high-pass filter When the gain of a filter is minimum at its center frequency, it is

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

Define and differentiate the following terms. Also Draw plots where required. You can use different symbols to denote each term a. Gain Cross over Frequency VS.Phase Cross over Frequency b. Phase Margin VS. Gain Margin c. Three Conditions of Stability in terms of phase cross-over frequency and gain-cross over frequency. Three Conditions of Stability in terms of phase margins and gain margins
What is an A/D converter with Voltage-to-Frequency Conversion (VFC)? What is the working principle?
6. An AC precision integrator is desired for a particular application to perform the operation: Vo'(t) = -1200 Vi(t) dt The primes indicate the ac portions of the respective functions. The lowest frequency other than a possible de component of the input signal is estimated to be 1.5 kHz. Determine a suitable design. 7. A low frequency differentiator is desired for a particular application n to perform the operation Vo(t) = -0.002 dvi(t)/ dt Based on a periodic signal with a frequency of 1 kHz, determine a suitable design. 8. Design an astable 555 timer circuit to produce 1kHz square wave, where TH = 0.35 ms and T₁ = 0.65 ms. Select C = 0.01 UE, Determine R₁ and Ra. 9. Design a monostable 555 timer circuit to produce an output pulse 5 ms wide. 10. Using op amps with Xsat = +/- 13 V, design a square/ triangular wave function generator circuit to generate 2 kHz triangular wave with a peak-to-peak voltage of 12 V. 11. Design a non inverting Schmitt trigger circuit with VT to be adjustable…
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
One advantage of having feedback in op amp circuit is A.Can control gain B.less complicated C.less input signal D.low gain E.high output voltage F.low bandwidth
Problem C It is desired to have a gain of 20 for frequencies up to 180 kHz. Determine the minimum unity gain frequency specification for the op amp. The gain should be within at least 98% Vsig Rin + Rf Vcc/-Vcc +12v/ -12V Vout
for the circuit if R = 5ohm, E = 20V and the cut-off (trigger) angle is 90 degrees; Draw the waveform of the source current Is, the output voltage VDC, and the output current Id Calculate the average value of output voltage VDC and output current Id.
5. The open-loop gain of a certain op-amp is 175,000. Its common-mode gain is 0.18. Determine the CMRR in decibels. 6. An op-amp datasheet specifies a CMRR of 300,000 and an A, of 90,000. What is the common-mode gain?
1- Mention any bwc advantages of integrated Circut. 2- For the circuit given below Vnis a sine wave Vinpp 11 Vand Vref-12V, Assume Vsat 1zv Name the circuit and drew the input and output waveforms. Vo Vin Vref 3- Explain why open-oop op-amp configurztions are not ues in linear applications Draw the biock diagram of opemp and define the funcion of each biock
write forward paths and feedback paths.
Six similar attenuators are used in an audio design and are linked in a cascade. The total attenuation is 80 decibels. The first section of the attenuator circuit has a 20 mV input. Determine (i) the attenuation in decibels provided by each individual attenuation stage, (ii) the output in volts of the final stage (iii) the output in volts of the fifth stage.
a- Zero. b- Slightly different from zero. O Maximum positive or negative. d- An amplified sin wave. 9-Negative feedback reduces @ The feedback fraction. b- Distortion. c- The input offset voltage. d- The open-loop gain. 10-The input impedance of a current-voltage converter is Small. b- Large. c- Ideally zero. d- Ideally infinite. a- 11-In a linear op-amp circuit, the @ Signal are always sin wave. b- Op-amp does not go into saturation. c- Input impedance is ideally infinite. d- Gain-bandwidth product is constant.