As an airplane's brakes are applied, the nose wheel exerts two forceson the end of the landing gear as shown. (Figure 1)Figure6 kN20da2 kN400 mm600 mmL1 of 1 >Part BDetermine the horizontal and vertical components of reaction at the pin C.Enter your answers numerically separated by a comma.15| ΑΣΦ | 11 | vec-2.66,6.55Cz, Cy=SubmitX Incorrect; Try Again; 5 attempts remainingPart CPrevious Answers Request AnswerDetermine the magnitude of the force in strut AB.Express your answer with the appropriate units.FAB =μAValueSubmit Request AnswerUnits??kN

According to the given dataWe need to find the reaction at point C and Force of AB

Answered: As an airplane's brakes are applied,…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

Consider the forces acting on the bracket shown in (Figure 1). Figure Submit VG ΑΣΦ 459 (F₁)z. (F1), (F₁) = Determine the coordinate angle y for F2.(Figure 1) Express your answer in degrees to three significant figures. Submit Request Answer (F2), (F2), (F2), = /30 ΑΣΦ | 11 60% F₂ = 600 N Submit Request Answer VAX 1 vec vec X Incorrect; Try Again; 4 attempts remaining F₁ = 450 N Previous Answers Request Answer Express the force F₁ as a Cartesian vector. Enter the components of the force separated by commas. Express your answers in newtons to three significant figures. ——| ΑΣΦ | |t | vec 195| | S 1 of 1 A @ GERIC ? Express the force 12 as a Cartesian vector. Enter the components of the force separated by commas. Express your answers in newtons to three significant figures, N ? ? N
42 in 64 [in]- 50 in D 59 in B این دو سال است اند اما او شده از این سامانه 63 in -10 in 21 in ( Given: The plate( The shaded rectangular volume) has weighs 240 lbf. It is. suspended bycable CD, Which D is wall anchor. So, Find the magnitude of force in the cable CD such the system is in static equilibrium??. Show all works.
Start this problem on a new sheet of paper. The structure shown is supported by a pin at A and roller at 8.F-277 N and d-76 mm Determine the support actions at pin C.Type the horizontal component in the field below. It must match what is on your paper. (Official Use Only 270512) 160 mm F- B d 80 mm 150 mm 100 mm
42 in 64 [in]- 50 in D 59 in B ی به سوالات فهد اما او شده وام بانک سامانه 63 in -10 in 21 in Given: The plate( The shaded rectangular volume) has weighs 240 lbf. It is. suspended bycable CD, Which D is wall anchor. So, Find the magnitude of force in the cable CD such the system is in static equilibrium??. Show all works.
In your response, please display the full computation and all FBDs that were used. Only round off at the final answer with 4 decimal places. P=2kN, F=3kN, and moment M=0.5kN-m are acting on the structure in the illustration. A pin at Z and a cable RQ connected by a connecting pin R support it. Im ● F ● P S TO M Im R lu W OZ a' 0.8m 3m If the pin support Z's factor of safety against shear stress is 3, determine whether a single or double shear should be provided for an economical and safe design. 4 m The mas allowable shear stress in the pin is 50MPa. Consider the following specifications. Single shear design: 25mm pin diameter Double shear design: 17mm pin diameter
Problem 4: Values: a = 300 mm b = 75 mm c = 100 mm Use the graphical method to break F into components parallel to bars AB and BC. If the component parallel to bar AB is 7 kN, what is the magnitude of F? Comments: B This is a perfect example of why the graphical method is useful - we are asked to resolve a force into components that are not perpendicular to one another. It's difficult to apply regular old sine and cosine (i.e. trig) for this because we're not dealing with right triangles. Instead we will use the law of sines and/or the law of cosines. • Start by drawing a vertical line to represent the vector F. Now draw a line parallel to AB passing through the top of F, and another line, also parallel to AB, through the bottom. Repeat for BC. You should have a parallelogram divided into two triangles by the resultant vector F. Pick one of the triangles to work with, use geometry to figure out the angles, and then apply the law of sines to compute the magnitude of F. Remember, these…
The offset slider-crank mechanism 50 mm, R3 = Ro 20 mm, R₂ = Write the loop closure equation. Solve for the position of the slider 4 as a function of 0₂. = O 2 is driven by the rotating crank 2. 140 mm B 3 4 OC X
Assign the values of shear force and bending moment to the image bar as a function of the x coordinate. q=20kN/m F=14kN M=12kNm L1=1.2m L2=1.4m L3=1.3m L4=1.5m Minimum value of shear force: Qmin = Maximum value of shear force: Qmax= Use units (kN,m), Do not round the invoices in the intermediate stages, but only the final answer!
ASAP
'Two Forces Shown in Fig. (1) acts on the bracket, determine the effect of these two forces (using Parallelogram method). 100 F₂=150N F₁-200 N
please send handwritten solution Q4 part e f g h complete
A cable BA shown in (Figure 1) is fixed so that the resultant force exerted on the pole is directed along its axis, from B toward O. Figure 2 m X -3 m F₂= 250 N F-300 N B 4 m 0 F=350 N 3 m 1 of 1 Determine the x and y coordinates of the end A of the cable BA Express your answers in meters to three significant figures separated by a comma. x, y = Submit Part B AΣo↓ vec Request Answer Submit 1 FR = Value Determine the magnitude of the resultant force. Express your answer to three significant figures and include the appropriate units. μA Request Answer < Return to Assignment wwwww Units Provide Feedback ww Hey ? ? m

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L