angle B ass

Q: What is Line J? ARROWHEAD .35mm 7.0- HIDDEN LINE 3mm K 01 5 0,5- 3. NOTE 5mm H. E. ABCO

A: Answer: The line "J" is called "section line". Therefore, the correct option is (C).

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: v to find angle alpha??

A: To find angle alpha

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: why is the angle 26.56 and then you use 22.56

A:

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: (Find the angle By using Law of sine's when (a= 100° , A=10.8, B=6 .A 33.16 .B 33 .c 33° .D 33.16°

A: a= 100∘A= 10.8B= 6   To find: Angle, b

Q: Tapered gibs are adjusted by screws spaced out along the length of the gib. Select one: O True O…

A: Tapered gibs

Q: Relative angles provide more information about segment position than absolute angles Select one:…

A: Given Data : Relative angles Absolute angles

Q: is 60 left or right?

A: The horizontal reaction at A: 60 kN (Right)......(Option D)

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: 0.75' C 4.5' Z 21-4 D A a 2 0.5' 2.5' B 10.5 X

A: (a) 2z ft(b) 0.5x+0.5y ft(c) -4.5x+0.75y+2.5z(d) -3.9x+y(e) 0.5x+0.5y-2z(f) 0.6x+0.25y-2.5z(g)…

Q: Analytically determine the maximum linear displacement of the cutting blade .75 S0 crank blade Your…

A:

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: Give the number of DOF and its type for each robot shown in Fig.Q1B:

A: Given:To find:Number of degrees of freedom and type of each robot.

Q: ths angle of the three forse acting on hook

A: given: determine the resultant and the angle of the three forces acting on hook?

Q: What is Line J? ARROWHEAD .35mm A 7.0 В

A: Solution:

Q: Give the horizontal and vertical distances from the upper left corner of this part to the center of…

A: The depth and dimension for the slot is 0.243 and for chamfer 0.089 depth. Hole A X…

Q: The rectangular lamina with breadth = 60 mm, depth = 30 mm. The Ixx value is _____________ mm4…

A:

Q: Why cos(60 if I don't see that angle in the figure

A: This question can be solved by labelling angles.

Q: Determine the sequence for the following figure

A: Given: To find: Sequence

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: Z is incorrect

A:

Q: What is the v-velocity at the centerline after refining the mesh

A: To explain: What is the v-velocity at the centerline after refining the mesh.

Q: What is Line G?

A: Solution:

Q: Select the correct statement about the notation circled in green and marked as letter E. Assume all…

A:

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: What is the diameter of the groove?

A: Let us discuss given engineering drawing to find diameter of groove.

Q: For the following internal dovetail, if bis 40mm greater than c, m is 60mm less than b, h is 25 mm…

A:

Q: slove f

A:

Q: For machine element, locate the centeroid

A: Answer:  Centroid ( 44.78 , 27.19 , 26.25 ) For a step-by-step solution have a look through the…

Q: 2y dx

A: Solution given below.

Q: What is a Couple Moment?

A:

Q: What line is K? A

A: What is line k

Q: How do you draw both triangles?

A:

Q: This is a Flange. What does The number 3 Represent

A:

Q: TAB Q 2 W 3 E 4 R bar Clockwise at % a 5 T 6 49 7 F7 8 F8 F9 The bar OB of bar AB 0.53m, and if the…

A: Length of bar OB, L1 = 0.53 m  Length of bar AB, L2 = 1.5 m  θ=390  Constant angular speed of bar…

Q: y is the angle an absolute value?

A:

Q: 5. According to the given 2 views, try to make the front full sectional view (7') and the left-side…

A: Given:- Top and side view   To find: Sectional A-A view and front view

Q: In the gear drive the addendum circle diameter of the gear is 300mm and the dedendum circle radius…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.