1- The compole is used to2- A 4-pole wave winding machine has ------ magnetic circuit.3- A commutator pitch for the duplex wave winding is equal to -4- A 2-pole triplex lap winding will have parallel paths.5- A 6-pole lap wound generator has 900 conductors. The e.mf induced per one turnbeing 3V. the generated voltage of the grnerator is( 6-A 10kW, 250 V shunt generator has armature and field resistance of 0.2 and 502respectively. Then the generated voltage isand

Note: We are authorized to answer three subparts at a time, since you have not mentioned which part…

Answered: and 1- The compole is used to - 2- A…

and 1- The compole is used to - 2- A 4-pole wave winding machine has ------- magnetic circuit. 3- A commutator pitch for the duplex wave winding is equal to

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Compare the characteristics of the following - Separately excited generators - Series wound…

Q: 1) analyse the resone behind the positive and negative tourqes produced by three phase syncronous…

A: As per our guidelines, we can only answer only one question at a time. Please resubmit the other…

Q: a single phase synchronous motor is sometimes referred to as a(an) ____ motor.

A: The solution is given below

Q: E-06, PC-05. Why are the iron cores of most induction coils laminated? O To increase the core…

A: core are laminated to tranfer efficient power from primary coil to secondary coil.

Q: The speed of a dc motor is directly proportional to the flux inversely proportional to applied…

Q: To change the direction of rotation of a series wound DC generator the general rule is to

A: To change the direction of rotation of a series wound DC generator Note: we always change the…

Q: Explain the need for connecting a capacitor in the auxiliary winding of a single phase induction…

A: A single phase induction motor is not self starting and therefore, it is necessary to making it self…

Q: component is fabricated using cast iron in an Induction motor. Bearings Stator frame Rotor stator…

A: 3-Phase Induction Motor- 3-Phase induction machine- When three-phase stator displaced by 120' is…

Q: 4- A double squirrel-cage induction motor has (a) Two series winding in stator (c) Two parallel…

A: In this question we will write answers related to induction motors...

Q: A 10-Pole, quadruplex wave winding machine will have a parallel path equal to___

A: Given data P=10 poles For Quadruplex. ,multiplicity (m)=4 Parallel paths A are no of paths for…

Q: D.C shunt generators are most suitable for arc winding

A: The most suitable DC genrator for arc welding is Differential compund genrator.

Q: In Wave winding of DC Machine the number of brush sets is equal to

A: In dc machine , depending upon the requirement machine is connected in lap or wave . depending on…

Q: fill inthe blank : field winding has large numberofturns of thin copper wire. a.…

A: Correct option is Shunt. shunt field winding has large number of turns of thin copper wire. Where…

Q: What are rotor faults in alternators

A: The rotor of an alternator is directly connected with field winding of the alternator whenever there…

Q: In long shunt DC generator Series field winding current Ise is equal to

A: -The circuit diagram for long shunt DC generator is given below:

Q: Draw the full-wave voltage doubler circuit diagram. If a 1:4 transformer is used in this circuit and…

A: Full-wave Voltage Doubler: As the name suggests, it is a circuit that provides twice the maximum…

Q: What is the difference between wound rotor induction machines and squirrel cage machines

A: The wound rotor (also called as slip ring) and squirrel cage machines are the type of rotor in…

Q: The stator and rotor of a 3-phase 6-pole squirrel cage induction motor has 54 and 42 slots…

A: Stator slots S1=54 Rotor slots S2=42 Stator -Rotor p=12

Q: Explain why rotator rotates in three phase induction motor

A: Induction Motor: The Induction motor is basically a rotating machine. It converts Three phase Ac…

Q: If dc generator of a simple 2- layers progressive wave winding has 21 number of slot and four poles,…

A: Given that simple two layer progressive wave winding two layer means 2 conductor in one slot Number…

Q: A 17-slot 33-segment armature is wound simplex-wave for four poles. Calculate the coil and…

A: Slots =17 33 segment armature ≈2 coil sides per slot Simplex wave P=4

Q: amature windings commonly used in DC machines a DC shunt generator are wound with a large numbe C…

A: 3. In Dc generator brushes are used to convertalterating current (ac) which is armature wlndingsto…

Q: In a 2 pole wave wound DC Machine has 620 conductors, the number of parallel paths is

Q: In induction type energy meter ,. is made up of Silicon Steel laminated assembly placed below the…

A: In induction type energy meter electromagnet is the main component of driving system whuch is…

Q: The brushes width in Wave winding is equal to a. 1.5 commutator segments. b. 1 of commutator…

A: brushed width in wave winding is equal to?

Q: mode of operation: e and rms value of load current e and rms value of thyristor current

A: The RMS load current per phase is given by:…

Q: How many parallel paths are there in the following armature windings: (a) six pole duplex-wave? (b)…

Q: For a full-wave phase control circuit draw the output voltage and current waveforms when firing…

Q: The field winding of DC generator has capable of carrying the full- load current and it is usually…

A: Given: The field winding of DC ________ generator has capable of carrying the full load current and…

Q: Flux ines are..to the surface of the poles If the poles are concentric to the rotation of a coil,…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: How many parallel paths are there in the armature winding of : (a) 36 slots, four pole,(b) 57 slots,…

Q: what is the advantage of a capacitor start induction run motor over a resistance start induction…

A: The advantage of capacitor-start induction-run motor over resistance-start induction-run motor is…

Q: Given the plot shown in the figure, what is the value of peak overshoot? jao j7= ja s-plane -3 --o4…

A: Using given pole zero plot calculator sets of the second order system. Now using peak over shoot of…

Q: Inter pole winding is connected in

A: Interpole :- These are tapered poles used in dc machines. Interpoles are used to reduce the armeture…

Q: Determine the commutator pitches Yc, trace the winding around the commutator and show that the…

A: Answer -

Q: common types of electrical failures of an AC induction motor

A: Electrical failures in AC induction motor is occurred when the insulation of winding get damaged ,…

Q: If dc generator of a simple two layers progressive wave winding has 21 number of slot and four…

A: Given the total number of slots is S=21 The number of poles is 4 The front pith formula for the…

Q: The DC ___________________ generator has both shunt and series ﬁeld winding which wound on to the…

A: The DC ___________________ generator has both shunt and series ﬁeld winding which wound on to the…

Q: Why do we need to clip a certain amount of voltage in positive or negative or on both sides? What is…

A: The explanation is as follows.

Q: 12) Welding generator will have A. Lap winding B. Wave winding C. Delta winding D. Duplex wave…

Q: draw a transformer-coupled half wave rectilinear with its input and output waveforms.explain how it…

Q: 1. Calculate the coil pitches and indicate the slots into which the first coils should be placed for…

A: NOTE: As per our company guidelines we are supposed to answer only first three sub-parts. kindly…

Q: The task is to draw or illustrate the armature winding, using the description below: -4…

A: 4 poles -26 conductors -double layer -simplex wave winding

Q: Workout the winding details of a 13 slots, 4-pole simplex wave wound d.c. armature with 4 coil sides…

Q: Assume that HOA SW 120 has been set in the AUTO position. List four ways by which coil CR-8 could be…

A: four ways by which coil CR-8 could be energized.

Q: Harmonics due to the presence of semiconductor devices in machine is called.. .. Answer:

A: Harmonics are Distortion in currents and voltage waveform due to the Non linear loads .

Q: The ripple factor for pure dc is

A: ripple factor = ripple voltage / average voltage but ripple voltage = sqrt ((RMS voltage)2-(average…

Q: What is the rms ac fault current

A: FAULT CURRENT :The fault current is the electrical current that travels across a circuit during an…

Concept explainers

Winding and Constructions

Alternating Current (AC) winding is generally of the 3-phase type due to the inherent advantages of the 3-phase machine. Armature coils must be connected to the yield balance (equivalent in magnitude and 2/3 of the series phase difference of the rod) 3-phase electromotive forces (emf). The armature should be divided into step-bands to start with slots around the perimeter.In the construction of AC machines, the frame is used as an external protective shield to protect it from environmental conditions. The frame also serves as the outer perimeter, allowing the interior to be easily placed. The static state section of the devices is the stator winding attached stator.

Question

1- The compole is used to
2- A 4-pole wave winding machine has ------ magnetic circuit.
3- A commutator pitch for the duplex wave winding is equal to -
4- A 2-pole triplex lap winding will have parallel paths.
5- A 6-pole lap wound generator has 900 conductors. The e.mf induced per one turn
being 3V. the generated voltage of the grnerator is
( 6-A 10kW, 250 V shunt generator has armature and field resistance of 0.2 and 502
respectively. Then the generated voltage is
and

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Winding and Construction of the Rotor and Stator

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux B) Mutual flux D) Leakage flux C) Total flux 5. The fundamental component of the magnetization current ------- the voltage applied to the core by ------ 90°: A) Lags, 45° B) Leads, 45°. D). Leads, 90°. C) Lags, 90°. 6. The ----- are resistive heating losses in the core of the transformer. A) Hysteresis losses. B) Copper losses. C) Leakage flux losses. D) Eddy current losses. 7. The total rotational losses of an induction motor are a combination of: A) Friction losses B) Windage losses. C) Core losses. D) Stray losses. 8. Induction motors are now the preferred A) absence of brushes. choice for industrial motors due to B) Small size. C) Less control requirements. D) rugged construction. 9. For an induction motor, if the synchronous speed is 1800 r/m, and the rotor speed 180rad/sec, then the slip will be: A) 5.5 % C) 6% B) 4.5% D) 4% 10. The lower the speed of an…
What are the similarities and dissimilarities of a 3-phase induction motor and a transformer?
Two 30 AC generators are such that one has twice the linear dimensions of the other. The field windings of each are excited to give identical sinusoidal air gap flux density waveform. Both have the same number of stator slots and identical winding patterns. The conductors per slot in big generator in K times that of the smaller one. The value of K to get equal no-load voltage at same frequency is (a)8 (b) 8 1 (d) 7 (c) 4
A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I 0000000000- N₁ № ₂ Z 00000 00000 Z N3 H I₁₂ I₁₂₁ ¹3
A small single-phase 60 Hz transformer has 10.2 W at no load. The core has a volume of 750 cm3. The maximum flux density is 10,000 G and the hysteresis constant of the core is 0.0005. Using the Steinmetz law on hysteresis loss, find the eddy current loss.
For 4 pole d.c machine armature winding with a double layer progressive simplex wave winding with 23 number of slots answer the following: a How many coils are present? b What is the coil span in terms of number of slots? c What is commutator pitch in terms of commutator segments? d How many coils are there between two consecutive commutator segments? e How many parallel paths are present?
1.Two identical shunt generators running in parallel, each with armature resistance of 0.02 ohms and field resistance of 50 ohms. The combined load current is 5000A. The field are so excited that the generated voltages of one machine is 610V and the other is 600V. The terminal voltage of this parallel combination will be. www Ish1 Rh1 a.350-360 V b.450-460 V c. 550-560V Rat www az G₂ Raz 5000 A Ish2
AC Machinery Fundamentals A three-phase delta-connected six-pole winding is installed in 36 slots on a stator. There are 150 turns of wire in each slot of the windings. All coils in each phase are connected in series. The flux per pole in the machine is 0.060 Wb, and the speed of rotation of the magnetic field is 1000 r/min. What are the resulting phase and terminal voltages?
A single phase 60 Hz transformer has its core volume of 1.5x10-3 cu m. The maximum flux density is 1.0 tesla and the hysteresis constant of the core is 6000. find the hysteresis loss.
Armature winding of an alternator can also be described as
1.) A 6-pole, 3-phase, 60-Hz alternator has 12 slots per pole and four conductors per slot. The winding is 5/6 pitch. There are 0.025 Wb entering the armature from each north pole, and this flux is sinusoidally distributed along the air gap. The armature coils are all connected in series. The winding is wye-connected. Determine the open circuit emf per phase of the alternator. Subject Electrical machine 2