For 4 pole d.c machine armature winding with a double layer progressive simplex wave winding with 23 number of slots answer the following: a How many coils are present? b What is the coil span in terms of number of slots? c What is commutator pitch in terms of commutator segments? d How many coils are there between two consecutive commutator segments? e How many parallel paths are present?

For 4 pole d.c machine armature winding with a double layer progressive simplex wave winding with 23 number of slots answer the following: a How many coils are present? b What is the coil span in terms of number of slots? c What is commutator pitch in terms of commutator segments? d How many coils are there between two consecutive commutator segments? e How many parallel paths are present?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.28MCQ

See similar textbooks

Similar questions

A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
What is capacitance voltage transformer?
For 6 polar D.C machine armature has 36 number of slots and the type of winding is a double layer simplex lap winding. a. How many coils are present? b. What is the coil span in terms of number of slots? c. If each coil has 4 turns, then what is the total number of armature conductors presents? d. How many parallel paths will be their in the armature? e. Altogether how many brushes will be their?
A small single-phase 60 Hz transformer has 10.2 W at no load. The core has a volume of 750 cm3. The maximum flux density is 10,000 G and the hysteresis constant of the core is 0.0005. Using the Steinmetz law on hysteresis loss, find the eddy current loss.
The resistances of potential transformer winding is minimized by using a thick conductors and small length of turns b thin conductors and small length of turns c thin conductors and large length of turns d thick conductors and large length of turns
E-06, PC-05. Why are the iron cores of most induction coils laminated? To increase the core permeability. To reduce the core reluctance. To reduce the effects of eddy currents. Click Save and Submit to save and submit. Click Save All Answers to save all answers. MacBook Air 吕0 F2 F3 F4 F5 $4 & 4 5 O 6 7 7 W .. E R .... S » D S F G # 3
4. The portion of the flux that goes through one of the transformer coils but not the other one is called. A) Average flux B) Mutual flux D) Leakage flux C) Total flux 5. The fundamental component of the magnetization current ------- the voltage applied to the core by ------ 90°: A) Lags, 45° B) Leads, 45°. D). Leads, 90°. C) Lags, 90°. 6. The ----- are resistive heating losses in the core of the transformer. A) Hysteresis losses. B) Copper losses. C) Leakage flux losses. D) Eddy current losses. 7. The total rotational losses of an induction motor are a combination of: A) Friction losses B) Windage losses. C) Core losses. D) Stray losses. 8. Induction motors are now the preferred A) absence of brushes. choice for industrial motors due to B) Small size. C) Less control requirements. D) rugged construction. 9. For an induction motor, if the synchronous speed is 1800 r/m, and the rotor speed 180rad/sec, then the slip will be: A) 5.5 % C) 6% B) 4.5% D) 4% 10. The lower the speed of an…
disadvantages of potential transformer.
Design a winding diagram given the following specifications. • Simplex Wave Progressive Winding • No. of Poles = 4 • Turn/coil = 1 • Conductor/Slot = 2 • No. of Commutator Segments = 27 • No. of Slots = 27 %3D
What is the effect of frequency on mutual induction of Transformer?
6- The transformer emf can be obtained by (a)By having a time-varying loop area in a static B field (b)By having a stationary loop in a time-varying B field (c) By having a time-varying loop area in a time-varying B field (d)None of the above
1- The compole is used to 2- A 4-pole wave winding machine has ------ magnetic circuit. 3- A commutator pitch for the duplex wave winding is equal to - 4- A 2-pole triplex lap winding will have parallel paths. 5- A 6-pole lap wound generator has 900 conductors. The e.mf induced per one turn being 3V. the generated voltage of the grnerator is ( 6-A 10kW, 250 V shunt generator has armature and field resistance of 0.2 and 502 respectively. Then the generated voltage is and