An RCC beam 200 mm wide and 450 mm deep, is reinforced with Fe415 grade steel of area 1000 mm² on tension side with an effective cover of 50 mm. If the shear reinforcement of 100 mm² stirrups is provided at a spacing of 150 mm centre to centre (c/c). What is the ultimate shear strength (V) corresponding to the shear reinforcement? 0 450 mm 400 mm beed 200 mm = 100 mm² Asv

An RCC beam 200 mm wide and 450 mm deep, is reinforced with Fe415 grade steel of area 1000 mm² on tension side with an effective cover of 50 mm. If the shear reinforcement of 100 mm² stirrups is provided at a spacing of 150 mm centre to centre (c/c). What is the ultimate shear strength (V) corresponding to the shear reinforcement? 0 450 mm 400 mm beed 200 mm = 100 mm² Asv

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 42 kN/m, LAB = 1.5 m, Lgc = 3.0m, and Lco = 1.5 m. %3D Consider the entire 6.0 m length of the beam and determine: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). B LAB LBC LCD WT305 x 41 Answer: (a) OmaxT MPа (b) omaxc МPа
1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
a two span beam subject to shear and flexure only is reinforced as follows: Section: TOP BARS @ midspan: 2-ø20mm @ face of supports: 5-ø20mm Section: BOTTOM BARS @midspan: 3-ø20mm @ face of supports: 2-ø20mm GIVEN: Stirrup diameter ds = 10mm concrete f'c= 21 mpa steel rebar fy= 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in a single layer. Determine the DESIGN moment strength of section at midspan for positive bending
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: kindly check below answer
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
Design a reinforcement of a doubly reinforced beam if the beam has a size of 425 mm x 600 mm. Use fc = 21MPa , fy = 414MPa
AWT305 x 41 standard steel shape is used to support the loads shown. Assume w= 58 kN/m, LAB = 1.8 m, LBc=3.6 m, and Lco = 1.8 m. Consider the entire 7.2 m length of the beam and determine: (a) the maximurm tensile bending stress at any location along the beam (enter a positive answer), and (b) the maximum compressive bending stress at any location along the beam (enter a negative answer). y LAB LBC LCD WT305 x 41 Answer: (a) Omax,T МPа (b) omax,C= МРа
A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows.1. Main reinforcement (short span i.e the bars are parallel to the short span), Y 12, shape code 34 @ 125 mm centre to centre,2. Distribution reinforcement (long span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,3. Concrete cover, 30mm,4. Concrete strength, 40MPa.Draw the reinforcement layout for this slab, in plan and section, indicating all the reinforcement and necessary information required by the contractor. You must calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Your drawing must be neat.
B4
1. A two span beam subjected to shear and flexure only is reinforced as follows: SECTION: TOP BARS @ MIDSPAN: 2-⌀20mm @ FACE OF SUPPORTS: 5-⌀20mm SECTION: BOTTOM BARS @ MIDSPAN: 3-⌀20 mm @ FACE IF SUPPORTS: 2-⌀20 mm Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: a. Design Moment strength of section at midspan for positive bending = ______ kN·m (nearest whole number)