An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.

An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

INSULATORS A string of suspension consists of four (4) units. The Voltage between each pin and earth is 0.14 of the Self-Capacitance of the unit. The Voltage between the Line Conductor and earth is 135 KV. Find the Voltage distribution across each unit. Draw the diagram.
Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The maximum Electric stress of the cable is
A string of suspension consists of four (4) units. The Voltage between each pin and earth is 0.05 of the Self-Capacitance of the unit. The Voltage between the Line Conductor and earth is 90 KV. Find the Voltage distribution across each unit. Draw the diagram.
12. There are 6 conductors in a double circuit line. Each conductor has a radius of 12 mm. The 6conductors are arranged horizontally. The center to center distance between the conductor is 2m. The sequence of conductors are from left to right as follows: a,b.c,a', b', c'. Calculate the inductance per km per phase of system. the a' 2 m 2 m 2 m 2 m 2 m
For same power transfer, same material and same length and same power loss. If the voltage is increased by 4 times. What will happen to the area of cross section of conductor?
Force on the conductor..gsgsggw
150 kv single core cable has a radius of cable of 5cm. The insulation martial has two layers. The relative permittivity of the first and second layers are 6 and 3 respectively. If the minimum electric stress of the first and second layers are 30 kv/cm and 20 kv/cm respectively. Find the maximum electric stress of the first layer s are
A three phase, 11 KV, underground cable system, consider a single core of conductor radius 0.5 cm diameter and lead sheath of 1.25 cm. The core and lead sheath have been separated by two intersheaths with radius 0.75 cm and 1 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same.
An over head transmission line supported from two towers location at the same level. The distance between the towers is 200 m. The tension in the wires is 9000 N. The weight of one meter of the conductor is 10 N. The sag of the wires is * 2.55 m 1.55 m 4.55 m 5.55 m Non of them
One advantages of load balancing is that each phase conductor carries the ? current value
33 kv single core cable has a radius of conductor of 0.6 cm. The insulation martial has two layers. The thickness of the first and second layers are 0.8 cm and 0.4 cm respectively. The relative permittivity of the first and second layers are 4 and 3 respectively. Find 3- The minimum electric stress of the second layer. 4- The minimum electric stress of the first layer.
A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.