An oscillator is built using a voltage amplifier with an inverting gain of magnitude A an input impedance rin = 10 k2 and an output impedance of r, = 100 2 (see Figure 6). The feedback loop t-network uses an inductor L = 10 µH and two capacitors C1 and C2. Design the circuit to oscillate at a frequency fo = 80 MHz knowing that in the lab there are only identical capacitors C = 1.5 nF. State any assumptions.

An oscillator is built using a voltage amplifier with an inverting gain of magnitude A an input impedance rin = 10 k2 and an output impedance of r, = 100 2 (see Figure 6). The feedback loop t-network uses an inductor L = 10 µH and two capacitors C1 and C2. Design the circuit to oscillate at a frequency fo = 80 MHz knowing that in the lab there are only identical capacitors C = 1.5 nF. State any assumptions.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider Figure 65. Compute for the minimum value of R3 if R₁ = R₂= 51kohms, C₁-C₂-0.001uF and R4=115.07kohms to start the oscillation. R3= kohms +Vcc Op-amp Output sinusoidal signal -VEE S= 4,1 Figure 65 K₂
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
3ZF The typical value of the out impedance of an op-amp is a.between 100 Ohms to little less than 1 KOhms b.less than 100 Ohms c.at least 10 percent of the input impedance d.equivalent to short circuit
Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator wilh R = 10OKOhms, C = 10UF and a sine wave inpul waveform, the output waveform is a cosine waveform. %3D ii. For an op-amp integrator with R = 100KOhms, C = 10uF and a triangular input waveform, the output waveform is a square wave. iii. For an op-amp integrator with R- 100KOhms, C =10uF and a sine wave input waveform, the output waveform is a sawtooth waveform. v. For an op-amp integrator with R10OKOhms. C lCuF and a square wave input waveform, the output waveform is a triangular waveferm.
Six similar attenuators are used in an audio design and are linked in a cascade. The total attenuation is 80 decibels. The first section of the attenuator circuit has a 20 mV input. Determine (i) the attenuation in decibels provided by each individual attenuation stage, (ii) the output in volts of the final stage (iii) the output in volts of the fifth stage.
Problem C It is desired to have a gain of 20 for frequencies up to 180 kHz. Determine the minimum unity gain frequency specification for the op amp. The gain should be within at least 98% Vsig Rin + Rf Vcc/-Vcc +12v/ -12V Vout
18 ut of estion 9 In Designing a lag compensator for the shown system, the only thing left is to determine the gain K. Take the closed loop poles ass-0.2 0.9. Determine Ke. R(s) Select one: O a. -7 O b. 1.06 O c. 2.50 O d. 1.94 Oe. 0.88 Ke $+0.5 $+0.05 lag compensator Consider the followin s(s+1) plant C()
Answer the following questions
3) Load for a circuit with direct current source voltage The waveform of the voltage generated on it is below shown. Source for this working circuit that is symmetrical The value of the voltage and load resistance is 100 V and 5Ω respectively.It is given as. Find what is required below. d) Find the effective value of the output voltage e) Total harmonic distortion in output voltageCalculate (THD)
what is the output waveform and phase shift of the integrator circuit given?
(ii). Determine the value of an inductor to be used in Colpitts oscillator to generate a frequency of 25 MHz. The circuit uses a value of C 200 pF and C2= 100 pE. Also, find the feedback fraction.