An open cylindrical tank with radius of 0.30 m and a height of 1.2 m is filled with water. Determine the spilled volume of the water if it was rotated by 90 rpm. Choices: a) 0.095 cu.m. b) 0.085 cu.m. c) 0.047 cu.m. d) 0.058 cu.m.

An open cylindrical tank with radius of 0.30 m and a height of 1.2 m is filled with water. Determine the spilled volume of the water if it was rotated by 90 rpm. Choices: a) 0.095 cu.m. b) 0.085 cu.m. c) 0.047 cu.m. d) 0.058 cu.m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A liquid having specific gravity of 2.0 is flowing in a 50mm diameter piper. The total head at a…

A: step 1-

Q: A 10cm diameter solid cylinder of height 10cm weighing 0.40kg is immersed in a liquid kg. (800)…

A: Given data Diameter of solid cylinder (d) = 10cm Height of solid cylinder(H) = 10cm Weight of…

Q: A tank has a pure water flowing into it at 12 L/min. The content of the tank are kept thoroughly…

Q: In a given setup as defined by the figure below, determine the rate of change in terms of h(t) given…

Q: Compute the discharge through a 1000 mm diameter pipe flowing at an velocity of 1.5 m/s.

A: Given: Diameter of pipe, d = 1000 mm Velocity, v = 1.5 m/s

Q: Q5: Determine discharge from the following current meter observation. Current meter equation…

A: Given, There are set of current meters readings are given In the above table.. Our aim is to…

Q: QI: An oil of S= 0. 8 is flowing through a venture meter having a diameter of (200- (0.5"your code…

A: To find coefficient of discharge

Q: A 950 me soda bottle weights 775 gram when ît is filled with sodo and 30 grams when empty. Determine…

Q: Answer within 3-5 sentences only. 1. What is the purpose of a Venturi meter? 2. What is a hydraulics…

Q: Two reservoirs, A and B, are connected together by the two pipes with a pump between them. Assuming…

Q: A tank is holding 6 gasses. The gasses exert the following partial pressures: 3.4atm, 3.3 atm, 3.9…

Q: Make a flowchart showing the procedure on design of structural steel beams with doubly-symmetric…

A: We have to draw a flow chart for showing the procedure on design of structural steel beams with…

Q: Gasoline (v = 4.06 E-7 m²/s) flows at 0.9 L/s through a 100-mm-diameter pipe. Describe the type of…

A: Given Kinematic viscosity = 4.06*10-7 m2/sec Dia of pipe = 100mm = 0.1 m Discharge= 0.9 lit/sec…

Q: Calculate length of the pipe required to bring down the concentration of chlorine from 6x105 CFU/L…

A: Given: Initial coliform concentration, Co = 6 x 105 CFU/L Maximum permissible coliform…

Q: A hydraulic pump is shown in the following Figure, flow rate is 25 L/min, the diameter of suction…

A: The given data is shown below: Flowrate=25L/minDiameter=25mmKinematic viscosity=30×10-6 m2/sDensity…

Q: Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

Q: You have been asked to provide a design for a rapid mix tank at a water treatment plant which has an…

Q: Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

Q: A cylinder of cross-sectional area 2657 mm² is filled with sand of permeability 16 cm/sec, water is…

A: Given Data Permeability of soil (K) = 16 cm/sec Time of testing (t) = 10 minute Cross sectional…

Q: Soda ash liquor having 1250 kg/m³ density and 1.2 cP viscosity flows through a 215m length of a…

A: Given: The density of soda ash liquor is 1250 kg/m³. The viscosity of the flow is 1.2 cP. The length…

Q: A liquid flow through pipe of diameter 10 cm a velocity of 6 cm Find the value of discharge

Q: Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

Q: 1-42 Water at 20°C from a garden hose fills a 2.0 L con- tainer in 2.85 s. Using unity converstion…

A: Units are very important to define any quantity, which helps to communicate. suppose someone takes a…

Q: 1. A cylindrical tank, 1.5m inside diameter has an orifice at its side 0.25m above the bottom. If…

A: Reference : Water resources, Orifices.Given :Diameter of orifice, height of water.To determine :1.…

Q: Calculate length of the pipe required to bring down the concentration of chlorine from 6x105 CFU/L…

A: Given: Initial chlorine concentration, Co = 6 x 105 CFU/L Permissible chlorine concentration, C =…

Q: A 189 mm diameter plunger is being pushed at 88 mm/sec into a tank filled with a fluid having sp.gr.…

Q: Quèstion 49 Avertical cylinder having a circular base of radius 'r and a height of 12 m is filled…

Q: Oil (sg-0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

A: Given data: B to D diameter = 18in D to E diameter = 8in

Q: Q1: An oil of S= 0. 8 is flowing through a venture meter having a 200- (0.5*your code number)) mm…

A: S=0.8 To find coefficient of discharge

Q: Venturi meter is used for measuring the flow rate of fluids in pipeline ..... Compressible O…

A: ANSWER: Both Top

Q: An open cylindrical vessel having a height equal to its diameter is half-filled with water and…

A: Find Angular velocity:ω=2πN60=2π(100)60=10.47radsLet the height And diameter be 'D'

Q: A cylindrical tank 10 ft. high and 4 ft in diameter placed so that its axis is horizontal. It is…

Q: Heavy fuel oil flows through 3 kilometers of cast iron pipe having a diameter of 250 mm. The…

A: Length of pipe (L) = 3 Km Diameter of pipe (d) = 250 mm = 0.25m Flow rate (Q) = 40 liters/sec…

Q: An open cylindrical tank with radius of 0.30 m and a height of 1.2 m is filled with water. Determine…

Q: A closed cylindrical tank is to be made using steel plates with a total area of 115 sq.m. What is…

Q: A liquid (sp.gr= 1.2) flows through a 150mm diameter pipe at a velocity of 4.5m/sec. Find (a) the…

A: Specific Gravity of liquid = 1.2 Density of Liquid = 1200 kg/m3 Diameter of pipe = 150 mm =0.150 m…

Q: Two tanks T and T' are each partially filled with 400 gallons of water. Initially, 250 pounds of…

A: To find amount of salt in tank T' This can be find through below equation

Q: 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the total weight…

A: Given: The diameter d1 is 70 mm. The diameter d2 is 35 mm. The time is 3 min. The weight is 3.5 kN.…

Q: A fluid is flowing in a pipe 8 inches in diameter with a mean velocity of 10 feet/second. The…

Q: An open cylindrical tank 4m in diameter and 10m high contains 4m of oil (s.g. = 0.80) and 6m of…

Concept explainers

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.

Question

An open cylindrical tank with radius of 0.30 m and
a height of 1.2 m is filled with water. Determine the
spilled volume of the water if it was rotated by 90
rpm.
Choices:
a) 0.095 cu.m.
b) 0.085 cu.m.
c) 0.047 cu.m.
d) 0.058 cu.m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Time and time related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Heavy oil discharges from a pipe through a sharp-crested, 100-mm-diameter orifice having discharge coefficient of 0.63. (a) What is the coefficient of velocity? (b) What is the velocity (m/s) of oil jet? (c) What is the head loss (m) through the orifice? 250 Orifice 1 Pipe OIL (SG = 0.91) MERCURY (SG = 13.6) NOTE: easurements are in 'mm' 350
Please answer in 5 mins a tank is initially filled of capacity of 25 L with brine having a salt concentration of 5 g/L. water containing 1 g/L of salt is entering at a rate of 4 L/min, and he mixture is allowed to flow out of the tank at a higher rate of 6L/min. find the concentration (g/L) of salt when the amount of water left in the tank is half the initial amount Topic applications in DE about mixture
Subject: Hydraulics What size of brass pipe would be required to carry standard gasoline at 80 degree Fahrenheit at a velocity of 10 ft. per second with a loss of head of 15 ft. per 100 ft?
An oil tank can be filled by pipe X in 5 hours and pipe Y in 4 hours, each pump working on its own. When the oil tank is full and the drainage hole is open, the oil is drained in 20 hours. If initially the tank was empty and someone started the two pumps together but left the drainage hole open, how many hours will it take for the tank to be filled? (Assume that the rate of drainage is independent of the Head)
Find the discharge in pipe 5 in L/s using the Hardy Cross method. (Use AQ<1 L/s as a threshold in your solution) If the discharge occurs in the counterclockwise direction, use a negative sign. 100 L/s K=1 Pipe 1 K=2 K=3 Pipe 3 Pipe 2 Pipe 4 K=2 Pipe S K=1 25 L/s 75 L/s h iPhone
Pls do it correct and neatly
Three liquids given the following properties are poured into the cylindrical container with a diameter of 3 meters and a height of 6 meters. First fluid poured: sg = 1.0 , V = 17.6715 m^3 Second fluid poured: sg = 0.81 , V = 10.6029 m^3 Third fluid poured: sg = 2.94 , V = 7.0686 m^3 Assuming that the container is closed after pouring the fluids and the stable state in the container is reached, determine the pressure at the height of 4-m from the bottom of the tank
Not sure how to do this one. Would appreciate a full solution, thanks!
Complete solution please. DECIMALS thank you Determine the head loss in feet in PIPE 1 Determine the head loss in feet in PIPE 5 Determine the velocity of flow in the lower branch, PIPE 3, in feet per second. Determine the velocity of flow in the upper branch, PIPE 2, in feet per second. Determine the velocity of flow in the lower branch, PIPE 4, in feet per second. Determine the head loss in feet in PIPE 2. Determine the head loss in feet in PIPE 3. Determine the head loss in feet in PIPE 4. Determine the total head loss in feet between the inlet A and the outlet B.
Part 1 Part 2 Part 3 hp A centrifugal pump having a 7.5-in-diameter impeller and the characteristics shown in the figure below is to be used to pump gasoline through 4000 ft of commercial steel 3-in.-diameter pipe. The pipe connects two reservoirs having open surfaces at the same elevation. Determine the flowrate. Do you think this pump is a good choice? This figure is referred to as the pump performance characteristics. 500 8 in. dia 400 7 出300 6 Head, ft 200 100 65 60 55 50 40 bhp 30 25 20 80 ° 40 120 160 200 240 280 320 Capacity, gal/min Write the system equation for this flow system as function of the friction factor f and volume flowrate Q in gal/min. (Use 2 significant digits on coefficients. Do not enter units as a part of your response.)
T Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the total weight of water passing through the meter in 5 minutes was 3.5 kN. A mercury differential gage connected to the inlet and throat of the meter showed an average mercury difference during that time of 300 mm. Determine the actual discharge if the same meter is used later on and a 250 mm difference is then observed. h = 300 mm Mercury, Hg Gs = assume, 4 significant figures 0