An open circuit contains a switch S, capacitor C, voltage source AVS and three resistors R1, R2, and R3. The capacitor is initially uncharged. At t = 0 the switch S is thrown to position A, and the capacitor starts charging. Then, at t = 4.70 s the switch is thrown to position B and the timer is reset (t' = 0). Find the rate which energy is being lost to Joule heating in resistor R₂ at t' = 3.00 s. Data: AVS = 50.0 V; R₁ = 10.2 km; R₂ = 20.0 kn; = 1.30 kn; C = 120 μF R3 =

An open circuit contains a switch S, capacitor C, voltage source AVS and three resistors R1, R2, and R3. The capacitor is initially uncharged. At t = 0 the switch S is thrown to position A, and the capacitor starts charging. Then, at t = 4.70 s the switch is thrown to position B and the timer is reset (t' = 0). Find the rate which energy is being lost to Joule heating in resistor R₂ at t' = 3.00 s. Data: AVS = 50.0 V; R₁ = 10.2 km; R₂ = 20.0 kn; = 1.30 kn; C = 120 μF R3 =

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

The symbol shown is a a. polarized capacitor. b. normally closed switch. c. normally open held closed switch. d. normally open contact.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.
QUICK A 100 µF capacitor in series w/ a 50-ohm resistance is connected suddenly across a 125-volt DC supply. What is the voltage in the capacitor after 10 ms? 79 V 100 V 108 V 125 V
When the switch is closed in above circuit, what is the voltage on the inductor, resistor R1 and R2 after 2.2us , assuming 0 V on the inductor to start?
The circuit in the figure below contains two resistors, R1 = 4.00kΩ and R2 = 5.00kΩ, and two capacitors, C1 = 4.00uF and C2 = 5.00uF, connected to a battery with emf E = 120V. If no charges exist on the capacitors before switch S is closed, determine the charge q1 on capacitor C1 1.00ms after the switch is closed. Determine the charge q2 on capacitor C2 1.00ms after the switch is closed.
What is the current in the inductor ILO in continuity mode before opening the switch. R₁ Select one: O a. I = O b. I = E R₁ R₂ R₁+R₂ = E R₂ O c. I=0 O d. I E R₁ E k R₂ ILO L
The potential difference is measured in .volt True O False O
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10