An inductor with inductance L = 0.400 H and negligible resistance is connected to a battery, a switch S, and two resistors, R1 = 11.0 N and R2 = 15.0 N (Figure 1). The battery has emf 96.0 V and negligible internal resistance. S is closed at t = 0 Part H When iz has half of its final value, what is i2? Express your answer with the appropriate units. HẢ i2 = Value Units Part I Figure < 1 of 1> When iz has half of its final value, what is i ? Express your answer with the appropriate units. HẢ R2 R1 i = Value Units

An inductor with inductance L = 0.400 H and negligible resistance is connected to a battery, a switch S, and two resistors, R1 = 11.0 N and R2 = 15.0 N (Figure 1). The battery has emf 96.0 V and negligible internal resistance. S is closed at t = 0 Part H When iz has half of its final value, what is i2? Express your answer with the appropriate units. HẢ i2 = Value Units Part I Figure < 1 of 1> When iz has half of its final value, what is i ? Express your answer with the appropriate units. HẢ R2 R1 i = Value Units

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
List the five capacitor replacement rules.
What is the unit of measurement for the strength of a capacitor? microamp microtorque microfarad microwatt
Convert the circuit from a T to a pi configuration
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
Calculate the voltage at 1.5¹ (milliseconds) for the following RC Circuit. Assume switch is closed and capacitor is in a charge state. t=0 LE -10 V oto R1 1kQ C1 1uF
Vcc = +12 V %3D a. Determine the following values for the fixed-bias configuration in the figure to the right. Rc IBo and ICO 2.2 k2 C2 RB 240 k2 ac output VCEQ, VB, and Vc 10 uF C ac input VCE B = 50 VBC 10 µF
A 470- uF capacitor is connected in series with a 120-k2 resistor. How long will it take the capacitor to charge completely?
What is the equivalent resistance ?? and what is the total inductance ??