An engine shaft running at 120 rpm is required to drive a machnie shaft by means of a belt. The pulley on the engine shaft is of 2m diameter and that of the machine shaft in 1m diameter. If the belt thickness is 5mm, determine the speed of the machine shaft. When 1) There is no slip 2) There is a slip of 3%

An engine shaft running at 120 rpm is required to drive a machnie shaft by means of a belt. The pulley on the engine shaft is of 2m diameter and that of the machine shaft in 1m diameter. If the belt thickness is 5mm, determine the speed of the machine shaft. When 1) There is no slip 2) There is a slip of 3%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.
Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact. answer with clear word please.
The 6-hp reducer motor can turn at 1200 rev/min. This shaft is made out of A-992 steel, has a diameter of 5/8 in, and it is 1.5 feet long. Calculate the angle of deformation in degrees at the end of the shaft.
Q: The sunwheel D has 20 teeth, the gear B is 50 teeth, internal gear C is fixed. The input shaft rotates at 2100 r.p.m. Determine the speed of the output shaft and the torque required to fix C when the gears are transmitting 30 kW. Output shaft Input shaft D
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate The maximum length of a path of the approach in mm.
This one may be a bit odd, but I can't seem to locate the proper term for a shaft with two flats 180° apart (i.e. one on top, one on bottom)
gearing arrangement suitable for the given application is.
For the steel shaft shown in Fig. Draw a torque diagram for the shaft. 17 ft kip 60 ft-kip 12 ft-kip 10 ft-kip 25 ft-kip
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate: a) The magnitude of the velocity of slip of gears in mesh. b)The maximum length of a path of the approach in mm c ) The length of a path of a recess in mm d) The addendum of the gears in mm e) The contact ratio.
A pair of gears, having 43 and 22 teeth respectively, are rotating in mesh, the speed of the smaller being 1600 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 20° involute form, addendum length is 5 mm and the module is 3 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact.
Q5: Select A suitable spline having a fit B for a gear to be mounted on a shaft with a diameter D= 60 mm. The gear transmits a torque of T=2.3 x 106 N.mm and has a hub length of L=100 mm.