An electric heater connected to a 120-V source consists of two identical 0.4-ohm elements made of Nichrome wire. The elements provide low heat when connected in series and high heat when connected in parallel. Find the power at low and high heat settings.

An electric heater connected to a 120-V source consists of two identical 0.4-ohm elements made of Nichrome wire. The elements provide low heat when connected in series and high heat when connected in parallel. Find the power at low and high heat settings.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

for The Gircuit shown in figure if (B =50) tind The values of CIe). and of Then express The change in value by apercentage + 15U RB, = 100Ka R82 = 50 KQ RE 3K2 %3D
Each terminal of a small polarity-independent incandescent bulb is connected to the positive terminals of two (2) DC voltage sources. The negative terminals of these sources are connected together. The first voltage source can have a range of value from 0-12, incrementable by 1.5 volts every turn of the rotary switch (i.e. 0 V, 1.5 V, 3 V, 4.5 V .... 12 V). The voltage of the second source is unknown. Using a luxmeter, the brightness of the lamp was measured for every increment of voltage of the first source. The following observations were recorded: a. 1.5 V produces a higher brightness than 3 V b. 0 V produces a higher brightness than 1.5 V c. 12 V produces higher brightness than 9 V d. 12 V produces equal brightness as 3 V What is the voltage of the second source? Justify each observation.
Identify the characteristics of AC and DC voltage. Runs at a higher temperature Answer 1Choose...DCAC More dangerous to transfer Answer 2Choose...DCAC Easy to produce Answer 3Choose...DCAC Easier to transform voltages Answer 4Choose...DCAC Voltage remains at a constant value Answer 5Choose...DCAC Cheaper to produce
THE POLARITY MARKINGS ON TWO WINDINGS MUST BE DETERMINED EXPERIMENTALLY. THE DEVICE FOR SUCH DETERMINATION IS SHOWN IN THE FIGURE BELOW. THAT THE TERMINAL CONNECTED TO THE POSITIVE TERMINAL OF THE BATTERY RESERVES THE POLARITY MARKING AS SHOWN IN THE FIGURE. WHEN THE SWITCH IS OPEN, THE DC VOLTMETER UNDERGOES A NEGATIVE DEFLECTION. WHERE ON THE CONNECTED WINDING SHOULD A POLARITY MARKING BE ATTACHED TO THE VOLTMETER? t = 0 R )cc VOLTIMETER VB- CHOOSE AN OPTION BELOW: A. POINT AT THE LOWER END OF THE INDUCTOR B. POINT AT THE TOP END OF THE INDUCTOR C. NONE OF THE OPTIONS D. A DOT AT THE TOP END AND BOTTOM END C E. THERE IS NO COUPLING BETWEEN THE INDUCTORS, SO IT IS NOT NECESSARY TO PLACE A DOT
I need the answer as soon as possible
2. Design a power supply by specifying their rating to the nearest standard values. C3 (220 VIEO H0 Deg RL Vwdg = 24vde 120 Ohm Eripplepk-pk = 0.75V Standard average current diode rating : 1A, 2A, 3A, 4A, 5A Standard peak current diode rating: 5A,10A, 15A Transformer: 200mA, 250mA, 500mA, 750mA, 1A, 2A, 5A
A platinum coil has a resistance of 3.146 at 40OC and 3.767 at 100OC. Find the resistance at 0OC and the temperature –coefficient of resistance at 40OC. Major Topic 8 Temperature coefficient of resistance EV Sco
A sinusoidal voltage has a value of 100 volts at 2.5 milliseconds and takes 20 milliseconds to complete one cycle. Then find the maximum cost and the time to reach it for the first time.
A resistor and a capacitor are connected in series across a supply of 250 Volts. When the supply frequency is 50 hz and the current in the circuit is 5 A. When the supply frequency is 60 hz, the current is 5.8 A. find C.
An inductance of 2 henrys and a resistance of 10 ohms are connected in series with an emf of E volts. If the current is initially zero, find the current at the end of 0.5 second when (a) E=120 volts, and (b) E=120 sin⁡6t volts.
A sinusoidal voltage has a value of 100 volts at 2.5 milliseconds and completes one cycle.It takes 20 milliseconds. Then find the maximum cost and the time to reach it for the first time
An example of Simple Resistive Circuits is ,