An aluminum rod is measured with a steel tape at 25°C. The reading is exactly 1.000 m long. Determine the steel tape measure's "reading" of the aluminum rod in the following cases. Will the "reading" be (1) more than, (2) the same as, or (3) less than 1.000 m? [Hint: A simple sketch for each case might be helpful. Both the aluminum rod and steel tape will expand or shrink as temperature changes.] [The coefficients of linear expansion for steel and aluminum are on the first page of this lab.] (a) only the steel tape is cooled to 0°C, (b) only the aluminum rod is cooled to 0°C, (c) both the steel tape and aluminum rod are cooled to 0°C,

An aluminum rod is measured with a steel tape at 25°C. The reading is exactly 1.000 m long. Determine the steel tape measure's "reading" of the aluminum rod in the following cases. Will the "reading" be (1) more than, (2) the same as, or (3) less than 1.000 m? [Hint: A simple sketch for each case might be helpful. Both the aluminum rod and steel tape will expand or shrink as temperature changes.] [The coefficients of linear expansion for steel and aluminum are on the first page of this lab.] (a) only the steel tape is cooled to 0°C, (b) only the aluminum rod is cooled to 0°C, (c) both the steel tape and aluminum rod are cooled to 0°C,

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

A spring requires 2 J to stretch from 1 m to 6 m. An additional 4 J is required to stretch the spring from 6 m to 8 m. What is the natural length of the spring in meters? Round your answer to the nearest hundredth if necessary. Provide your answer below: m
Answer is 17.4N horizontally and 17.8N vertically.Please show steps in detail.
1 Question 2(a): 2 A steel surveyor's tape is to be used to measure the length of a line. The tape has a rectangular section of 2 cm by 0.5 cm and a length of 100 cm when 7, and the tension or pull 3 4 on the tape is AA N. Determine the true length of the line if the tape shows the reading to be 5 BB cm when used with a pull of CC N at Te ground on which it is placed is flat. 6 7 Take: 8 °C T₁ = 55 P P 9 T₂ 85 °C = 10 AA = 20 N 2 cm 11 BB = 463.2 cm 12 CC= 35 N 0.5 cm 13 12010)/°C 14 = 200 G Pa 15 16 17 Solution: 18 cm 19 20 cm 21 22 L= 463.2 + cm Ans 23 24 Question 2(b): 25 Three bars each made of different materials are connected together and placed between two 26 walls when the temperature is T. Determine the force exerted on the rigid supports when 27 the temperature becomes T . The material properties and cross-sectional area of each 28 bar are given in the figure. Steel Brass 29 E 200 GPa 30 Take: Ebr 12(10-)/°C abr 100 GPa 21(106)/C Copper Eu = 120 GPa cu = 17(10)/C Acu - 515…
A cylinder with a 1.5-inch diameter piston exerts 6500 lb of extension force.. What is the cylinder pressure? State your answer in psi to the nearest whole number.
Question 2(a) : A steel surveyor's tape is to be used to measure the length of a line. The tape has a rectangular section of 2 cm by 0.5 cm and a length of 100 cm when T, and the tension or pull on the tape is AA N. Determine the true length of the line if the tape shows the reading to be BB cm when used v Formula Bar N at T,The ground on which it is placed is flat. Take: T = 63 °C P P 93 °C T, АА - 20 N 2 ст BB = 463.28 ст СС - 35 N 0.5 ст 12(10*)/°C -6 Et 200 GPa Solution : 8, = Ξα ΔΤL= cm PL 8 = AE Page 1 ст L = 463.28 + cm Ans Question 2(b) : Three bars each made of different materials are connected together and placed between two walls when the temperature is T . Determine the force exerted on the rigid supports when the temperature becomes bar are given in the figure. T, . The material properties and cross-sectional area of each Steel Brass Сорper Est = 200 GPa ast = 12(10¬)/°C _@br = 21(10¬6)/°C acu = Epr = 100 GPa Take : Ecu = 120 GPa 17(10-6)/°C T = 12 °C Acu = 515 mm² 21 °C…
Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a constant temperature of 32 °C on both sides using an electric heater generating heat at a rate of Q = 0.5 W which is dissipated to air from both sides of the plate. Consider the temperature of the wind/air as 20 °C and assume that the wind speed does not exceed 100 m/s. The properties of air at this temperature are given as; specific heat capacity Cp = 1.005 kJ/kg-K, thermal conductivity k = 0.0253 W/m-K, Density p = 1.19 kg/m³, and kinematic viscosity v = 1.522 x 10 5 m²/s.
Find the circumference and the area of a circle with diameter 10 cm. Write your answers in terms of t, and be sure to include the correct units in your answers. (a) Circumference: 10 cm (b) Area:
answer this; The numerical value of ? can be calculated as mm
0.5mlm 1 3 4 5 cm mm} Consider the steel ruler shown. Which of the following dimensions can be accurately measured with this ruler? C. 1.05 mm B. 1.5 mm A. 1.25 mm D. All of these dimensions can be measured accurately
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 80.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.70 MN, pressure vessel bolts aide port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.
kindly help me with this one. Write your answer with four decimal places and enclose them in a box. Solve as neatly as possible. A sheet of Invar is 0.60in. thick and the temperatures at the two faces are 402degF and 222degF. Compute (a) the heat flux through the Invar sheet; (b) heat loss per hour if the are of the sheet is 6.4 square feet; (c) heat loss per hour if pyrex glass instead of Invar is used; and (d) heat lost if Invar is used and the thickness is increased by 0.80in.
Ixo and Iyo of a quarter circle with a diameter of 50cm (Answer format: Ixo= , Iyo=)