mhot Thot = 75°C Tout-? %3D mcold Tcold = 18°C Hot and cold stream of water are mixing together as shown in Figure. The temperature of the hot and cold streams at the inlet are 75 °C and 18 °C, respectively. Mass flow rates of the hot and the cold streams are (1.50x10^-1) kg and (1.000x10^-1) kg, respectively. Find the temperature of the mixed stream. The specific heat of the hot water stream is 4000 J/kg-K and the cold stream is 3800 J/kg-K. Answer should be in °C with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Activate Go ta Setie x10

mhot Thot = 75°C Tout-? %3D mcold Tcold = 18°C Hot and cold stream of water are mixing together as shown in Figure. The temperature of the hot and cold streams at the inlet are 75 °C and 18 °C, respectively. Mass flow rates of the hot and the cold streams are (1.50x10^-1) kg and (1.000x10^-1) kg, respectively. Find the temperature of the mixed stream. The specific heat of the hot water stream is 4000 J/kg-K and the cold stream is 3800 J/kg-K. Answer should be in °C with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Activate Go ta Setie x10

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Similar questions

mnot Tnot = 75°C Tout-? %3D mcold Tcod = 18°C %3D Hot and cold stream of water are mixing together as shown in Figure. The temperature of the hot and cold streams at the inlet are 75 deg-C and 18 deg-C, respectively. Mass flow rates of the hot and the cold streams are (1.50x10^-1) kg and (1.000x10^-1) kg, respectively. Find the temperature of the mixed stream. The specific heat of the hot water stream is 4000 J/kg-K and the cold stream is 3800 J/kg-K. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: х10 Answer
Soda from a ms=12oz can at temperature Ts=16 degrees celcius is poured in its entirety into a glass containing a mass mi=0.14kg amount of ice at temperature Ti=-18.5 degrees celcius. Assume that ice and water have the following specifc heats: ci=2090J/(kg*C) and cs=4186 J/(kg*C), and the latent heat of fusion of ice is Lf=334 kJ/kg. In this problem you can assume that 1kg of either soda or water corresponds to 35.273oz. a.) in degrees celcius, what is the final temp of the mixture? b.) find an expression for how much of the ice has melted. c.) in kg, how much of the ice has melted?
A 0.6 m3 tank contains gas at a pressure of 5800 kPa gage, a temperature of 75 deg. Celsius and mass of 25 kg. A part of this gas was discharged and the temperature and pressure changed to 60deg. Celsius and 4130 kPa respectively. Heat was applied and the temperature was back to 75 deg. Celsius. Find: (a) the final mass in the tank in kg CHOICES 9.36 15.63 18.283 (b) the discharged mass in kg. CHOICES 6.716 15.63 9.36 (c) the final pressure of the gas in kPa gage CHOICES 4215.56 5135.88 4135.88
Please Solve only if you are 100% Sure , Don't make any kind of Mistake. Show all the work ,if possible attach Steam Table. 1)what is the state of steam at 623 K and 90 bar pressure? Determine the specfic entropy of this steam
96 %24 ork 6 1. A patient needing a blood transfusion has a blood pressure of 120/70 (this is in units of mm Hg). It is best for the blood during the transfusion, to have a pressure that matches the patient's diastolic pressure (70 mm Hg). At what height, above the insertion point, should the blood supply be raised, such that it has the desired pressure of 70 mmHg is reached? (Density of blood is 1.06 * 10^3 kg/m^3 and 1 mm Hg= 133 Pascals) PZ =P0+PGZ 1.013 *105PA760MMHG G=9.8 P=1000 dy 12 f5 114 144 & 9 5. 4. 00
(30 pts) AIR P const. Wpw 85 L of air at 250 kPa and 25 °C is contained in an insulated piston-cylinder device shown in the figure. If the pressure remains constant and the paddle wheel does work of 30 kJ, what is the final temperature of the air? State your assumptions clearly.
If air is heated at constant pressure from 1.7 m3, 27 °C and 97 kPa to 417 °C. It is then cooled at constant volume back to its initial temperature Which is figure depicts the processes? Conipr- A Vg=Uz B. N2
Q1/ A boiler working at a pressure of 1.4 MPa evaporates 8 kg of water per kg of coal from feed water entering at 40C. The steam at the stop value is 0.95 quality. Determine the equivalent evaporation from and at 100C.
Mr Luda wants to understand further about a newly created gas. The gas is initiallyat a pressure of 90 kPa, volume of 1.258 m3 and temperature of 10°C (State 1).The gas undergoes a 3-step process in which it is first compressed isothermally toa pressure of 400 kPa and volume of 0.283 m3 (State 2), then expanded at constantpressure back to its original volume (State 3). Finally, the gas is returned to itsoriginal State 1 by cooling at constant volume.a) Sketch the cycle of this system on a P – V diagram.b) Calculate the work done (in kJ) for each process step.c) Determine the total work done for the three-process cycle.d) State whether the work done is on or by the system.
Ammonia and air pass through the heat exchanger. While the ammonia is entering as asuperheated vapor at 16 bar pressure and 60C temperature it is leaving as a saturated liquid at thesame pressure but unknown temperature. The ammonia mass flow rate is 400 kg/hour.Air is flowing backward and is heated from 17C to 42C at the constant pressure of 2 bars.NOTE: Find air properties from https://www.peacesoftware.de/einigewerte/luft_e.html a. Draw the ammonia T-v diagram showing the stages, pressures, and temperatures b. How much heat is transferred from ammonia to air assuming no heat transfer to thesurroundings? c.Determine air mass flow rate Please show all steps in solution thanks
What are the specific volume, specific internal energy, specific enthalpy andspecific entropy of steam at 1.50 Mpa and temperature is 180 oC?
Benzene at 20 0C is pumped from one storage tank to a reactor (density=878 kg/ m3 ). Volumetric flow rate of benzene is 9.5x 10-4 m3 /s. The difference in the elevations of the two unit is 40m. The tank whichserves as a source is open to the atmosphere while the tank which receives the benzene has a pressure of P2 kPa abs in the vapor space above the benzene. 1‐in, schedule‐40 steel pipe and 2‐in Sch‐40 steel pipe isused in suction and discharge line respectively. Total friction loss of the system given as 135 J/kg . Pressure gauges in the pipeline at the inlet and outlet of the pump read (P3) 34.5kPa and (P4) 1051.6kPa, respectively. Efficiency of pump is %75 a) Calculate the power of pump (kW). (Fluid Mechanics Question) (Please answer it detailed and step by step)