Answered: An A-frame shown is supported by a…

An A-frame shown is supported by a hinge at A and a roller at E. Compute the total forces at B, C, and D. 1.8m 240 kN B Im 1.2m A 800 -0.5m 1.8m -0.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. The truck is moving along a 20 m span of beam. The front axle is 30 kN, the middle is 75 kN an…

A: P1 = 45KN P2 = 75KN P3 = 30KN

Q: w = 3 kips/ft 11'

A: Given:- w=3kips/ft To find:- (a) The reactions at support A. (b) The axial forces in all links.…

Q: What is the vertical reaction at the fixed support? I 4 kips/ft 4 kips/ft E 6 ft 3 ft ++ 3 ft -

Q: The vertical mast supports the 3.0-kN force Fand is constrained by the two fixed cables BC and BD…

A: Given:- The magnitude of the force = F = 3 kN The force is constrained by two fixed cables i.e. BC…

Q: The axial force in member CB equals 50 kN 100 kN 100 kN 50 kN -3.0- -3.0- -3.0- AV 2.0 m B.

A: To find ,axial force in CB

Q: Praw shear force (S.F) and bending moment dingram (B.H). Support A Hinge. E Roller, Pa 20 KN Wa6…

A: Data Given: Asked: Draw SF and BM diagram

Q: 600 + C (Ib) E 450 + B (Ib) |A 30° В -3 ft- -3 ft-

Q: 12 ft 8 ft 8 ft F G 8 ft D 6 ft 6 ft 00 00

Q: *4-100. Replace the force system acting on the beam by an equivalent force and couple moment at…

Q: Determine the force in members DE, OE, LE, and LK. M K 2 m 2 m A D E F GH 2 kN 2 kN 5 kN 3 kN 16 m,…

Q: Problem 1) The rod below cannot rotate at the support A, however the slider is free to move up and…

Q: Determine the vertical reaction at each support (A,, B,, Cy, D, and E,) for the beam below. 15 KN/m…

Q: The moving load is transmitted to the bottom chord of the truss. F G 3 m B C D 3 panels at 4 m = 12…

A: considering joint d

Q: 2 kN Problem 1 0.3 m Calculate the force in member BD and the reaction at the roller support for the…

Q: Determine the support reactions for the truss loaded with uniform wind load shown. 9 kN/m 6 kN/m…

A: Draw FBD:

Q: There is a pin support at A, a roller support at D, and an overhang of 2m. Sol 5kN/m

Q: Determine horizontal reaction at A of the given indeterminate truss below. 80 KN 6 AN 5 m EA =…

A: degree of indeterminacy calculation: internal indeterminacy external indeterminacy

Q: Determine all the support reaction of the given figure 8 KN/m pin D A hinged 2m 20 KN 2m pin 1881 O…

Q: The pin-connected structure consists of two cold-rolled steel [E = 31,000 ksi] bars (1) and a bronze…

A: Calculate the area required for bar (2) so that each bar carries the same force.

Q: 02- 3. A truss is loaded as shown. Using the knowledge of statics, derive a set of equations to…

Q: 10 ft 2k/ft D 16 ft В 60 k 8 ft A Prob 2) Draw the moment diagram for the real loads on the…

Q: Compute the force in all members of the truss shown in Fig. T-08. 50 KN 30 KN MATHalino.com B 4 m 5m…

Q: 250 kN 116 kN 71 kN 208 kN 61 m 54 m 54 ml

A: GIVEN GIRDER SYSTEM

Q: 8 kN C 2m 1 (3) 15 kN - 2m- -2m-

Q: 6. Determine the vertical reaction at the pin support A if Pe= 32 kN. 18.75 kN b. 26.25 kN 1 m H a.…

A: As per guidelines we can solve one question at a time please upload separately,Thanks Solution to…

Q: Determine the maximum moment considering only the span where the uniform load is applied. (in kN-m)…

A: Given A beam,

Q: A couple acting on the winch at G slowly raises the load W by means of a rope that runs around the…

A: Given:- The length of each panel = L The magnitude of the load attached to the derrick at A and B =…

Q: The chain hoist on the wall crane can be placed anywhere along the boom (0.1 m < x < 3.4 m)…

A: Consider a chain hoist placed on a wall crane and is acted upon by a vertical load at point D and…

Q: The beam is made up of four boards, and is subjected to a moment of M=200 kip in, calculate the…

A: Due to the moment top board will be in compression , we have to find out the compressive stress…

Q: 60 kN• m |5 kN 2 kN/m 3 kN/m Hinge B 10 m 6 m 4 m 6 m 6 m

A: Given data: Hinge at B.

Q: 6 kN/m A- -3 m 6 m B

A: Given data:

Q: H.W. Determine the horizontal and vertical components of force at pins A and D. 2m 03 m |B -1.5 m-…

A: Given:- A system is given with 12 kN load is applied at Point E To determine:- The horizontal and…

Q: Determine the reaction at middle support, in kN, of the continuous beam below. 5 kN/m 1.5m- 1.5m-

Q: 1. A frame held taut by a rope connected at D and E, is pin connected at B. If 1500 N is…

Q: ermine the bar forces at BE, CE, the truss shown 4 KN 1.2 KN B F. 2.0m H 1.5m 1.5 m 1.5 m 1.5 m 1.2…

Q: A Y kN/m 12 m The support at B can be assumed to be a roller. 1. What is the reaction at A? (kN) 2.…

Q: From the truss figure on the right, determine the: 1. Moment at A 2. Resultant Reaction at A 20 N E…

A: Multiple sub-parts As per the company's guidelines we can only solve first three(3) sub-parts,…

Q: w = 2P/L A B C 0.6L 0.2L 0.2L

Q: Determine the reaction at the roller support and draw the bending moment diagram for the beam and…

A: Fixed end moment at the point B - MB = 60×2×1.2 + 22 +120×.5⇒MB = 324 KN-m Force in the vertical…

Q: The 2-lb collar is released from rest at A and slides freely up the inclined rod, striking the stop…

A: For the given arrangement,

Q: The vertical mast supports the 4.8-kN force F and is constrained by the two fixed cables BC and BD…

A: Calculate the tension T1 in BD. Can this be accomplished by using only one equation of equilibrium?

Q: A 3m 10N FV 1m 15N G 2m C 2m D 2m 10N H 1m E 3m B

Q: Find the internal force system acting on section 3 for the pin-connected frame. 240 N 0.3 m 240 N0…

A: The internal force is the force emitted by the objects in the system. While internal forces may…

Q: For the given beam: A 4m дв B 4m C 8m D 3m E 3m F

A: Given: Overhanging beam Dead load Live load To find: Absolute maximum moment Note : Below part…

Q: E D F A

Q: Determine the vertical reaction at B of the given indeterminate frame below. -15 ft 15 ft C B D 15…

A: According to fixied end momentsMFBC…

Q: A 2 m O - 6 m 1 KN 4 KN 1 m 3 m 6 KN

Q: Using the given frame, find the vertical and horizontal reaction at support D. (kN) 30 kN/m 50 kN…

Q: An A-frame shown is supported by a hinge at A and a roller at E. Compute the total forces at B, C,…

A: To find total forces at point B,C,D

Q: Construct the influence lines of each truss member. H 4 m B C E 6@3 m = 18 m

Question

An A-frame shown is supported by a hinge at A and a roller at E.
Compute the total forces at B, C, and D.
1.8m
240 kN
Im
1.2m
800
-0.5m
1.8m
0.5m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The frame shown in Figure is supported by a hinge at E and a roller at D. Compute the horizontal and vertical components of the hinge force at C as it acts upon BD. 45° -2m- 24 KN C -4m- -1m- 45° B E
Determine the vertical force P which must be applied at G so that the linkage is in equilibrium for the position shown. 125 mm 300 mm C 125 mm 9 N-m B 180 N 250 mm F. G 100 mm 100 mm
W=20kN/m 2m -1.5m. 100kN -0.5m B CROSS SECTION OF BEAM AB 30mm 30mm CALCULATE MAXIMUM BENDING AND SHEARING STRESS IN THE BEAM. 100mm 60mm 30mm 160mm 30mm
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F E b G B b b C a Q Zoom image Compute the force on member CL P
Analyze the frame shown and draw the shear, moment and axial diagram. b d 3m 25kN - 4 m e1.5 m a. 2 at 4 m = 8 m
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c = 5m 5 panels@(a)m each F E b B b b P G C Zoom image Compute the force induced in member AB
2/88 If the resultant of the forces shown passes through point A, determine the magnitude of the unknown tension Tz which acts on the braked pulley. 275 N 1600 N 0.5 1.5 m -1.8 m m -300 N 1.25 m B 50 0.6 m 650 N
Situation 5. The K-truss is loaded by vertical force and supported by pin and rollers as shown. 18. Detemine the force in member ES 6 panels at 8' c. 7.547 kips (T) d. 5.721 kips (T) B. a. 3.774 kips (C) b. 6.038 kips (C) E A G 5° T 19. Determine the force in member CD R c. 6.400 kips (T) d. 5.800 kips (T) a. 3.200 kips (C) b. 4.800 kips (C) 20. Determine the force in member KR a. 0 b. 2.120 kips (T) H. M K 1 kip 2 kips 4 kips c. 1.887 kips (C) d. 2.544 kips (T) 20 21. Determine the force in member DK a. 2.000 kips (T) b. 0 c. 3.200 kips (T) d. 1.000 kips (T)
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 8=15⁰ a = 3m b=3m c= 5m 5 panels@(a)m each D E b G P b b K C Zoom image Compute the force induced in member CD. C B
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F D E b G B Ө 0 P b b C Zoom image Compute the force induced in member DB. C P
The horizontal force F acts on the handle of the wrench (i.e Fis parallel to xy-plane). What is x-component of the moment of this force about the origin "O"? F = 19.5 N, a = 36 mm, b = 200 mm, c = 10 mm, 0 30°. of B
The beam is supported by a pin at A, a spring having a stiffness at B, and a roller at C. Determine the deflection at B. EI is 40788045.2 kNm². a. 1.50 mm b. 0.404 mm c. 1.40 mm d. 0.912 mm