An 30 dB attenuator is made using 1W rated resistors found in a lab. Assume a power source with Rs = 50ohms) delivers 100W into the attenuator with a 50 ohm load connected, 1. How much power in watts is disipated at the output? 2. How much power is dissipated by the attenuator in WATTS 3. What is the Vpk input voltage that is seen at the attenuators input terminals 4. What is the Vpk voltage that is seen at the load connected to the output of the attenuator? 5. Is this a matched system? If so, why is it important to have a matched system?

An 30 dB attenuator is made using 1W rated resistors found in a lab. Assume a power source with Rs = 50ohms) delivers 100W into the attenuator with a 50 ohm load connected, 1. How much power in watts is disipated at the output? 2. How much power is dissipated by the attenuator in WATTS 3. What is the Vpk input voltage that is seen at the attenuators input terminals 4. What is the Vpk voltage that is seen at the load connected to the output of the attenuator? 5. Is this a matched system? If so, why is it important to have a matched system?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q??
7 Name the circuit shown below? Please justify the name with brief explanation of the working of this circuit. Page 3 of 6 Final Assignment If the input signal is a high frequency input signal to an AM receiver (very less amplitude) will this serve the purpose. If Yes Justify? If NO Justify and give the modification which will make it suitable for the above mentioned purpose. out RL
4. The power dissipated in a resistance is equal to ..in non-sinusoidal input signal.
N-channel Mosfet compared to P channel mosfetWhich of the following is true?A) It is faster.B) It has a lower input impedance.C) It has a lower noise level.D) none
For an AM DSBFC modulator with a carrier frequency f. = 100 kHz and a maximum modu- lating signal fm(max) = 5 kHz, determine a. Frequency limits for the upper and lower sidebands. b. Bandwidth. c. Upper and lower side frequencies produced when the modulating signal is a single- frequency 3-kHz tone. Then d. Sketch the output frequency spectrum.
Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Voludit) Vm = 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. = 0.1 V (assume ideal diodes) T=0.01 sec. tisec)
Powered by ±10VIntegrator circuit designed with Op-AmpVin=3sin(2π400t) alternative signal to inputhas been applied. Analysis of output voltage (Vo)Draw the waveform.Calculate the maximum and rms value of out signal.
d) A regulator as shown in Figure 4 has an input voltage, Vs 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L= 200 µH, filter capacitance, C = 440 µF. The average load current, la = 1.25 A. Determine the; i. average output voltage, Va. ii. peak-to-peak output ripple voltage, AVc. iii. peak-to-peak output ripple current of inductor, AI. iv. peak current of the transistor, Ip. v. critical values of L and C. vi. critical values of L and C if Vs is increased to 14 V. Estimate the change in percentage for the critical values of L and C. V, Load V V G Figure 4
Write about two applications for a series circuit, (Think about the different electronics at home or at work), and some of the advantages and disadvantages?
An ideal boost converter is utilized in designing a PV storage system. The boost converter is operating at the boundary layer between the continuos conduction mode and discontinuous conduction mode. Design the mathematical model of the switching frequency for this boost converter in terms of load, duty cycle and inductance under the above operating conditions.
H3
18 Time taken for the output signal rise to 95% from 10% is called rise time Select one: True False