ideally, what should the reactance of a bypass capacitor be in order to eliminate a 10 kHz AC voltage at a given point in an amplifier circuit?

Q: 252 M + vi(t) 0.1 F + 1H2v₁ (t) For the circuit shown, vi(t) = 10 u(-t) + 20 u(t). voltage v₁ (t) =

A:

Q: c. For the circuit shown in Figure, determine lc and VCB. Assume the transistor to be made of…

A:

Q: Draw the signal after adding -2.5 DC level with the given signal, sketch the new output signal and…

A:

Q: True or False: A Higher sampling frequency results in a more accurate analog signal recreation…

A: The sampling frequency is the average number of samples obtained in one second .

Q: resistive load. It is supplied by a DC power source of magnitude Vs = 160 V. The switching period is…

A:

Q: a) In an ac transistor amplifier, the circuit includes capacitors as well as resistors. What is the…

A: Brief description: In the above given question we need to explain importance of coupling capacitors…

Q: Given the differential amplifier circuit below. Determine the following: emitter current,…

A:

Q: Figure 2.a shows a transformer-coupled class A amplifier, and Figure 2.b shows the transistor's…

A: Given

Q: Ideally, a dc load line is a straight line drawn on the collector characteristic curves between…

A: A dc load line is straight line drawn on the collector characteristics curve between

Q: Q. What is the purpose of using DC supply in amplifiers & oscillators circuits? *

A: AMPLIFIER: An amplifier is a circuit that boosts the signal's amplitude by amplifying a weak signal.…

Q: For a series ac circuit having resistive and reactive components, How do you determine the active…

A: In this question we will find active power consumed in series AC circuit...

Q: R1 IK + + R2 VR2 Vk e(t)( R1=12, R2=12, E=8V, e(t)=0.037 Cos2t Ig = V – 2VK

A: Operating point of the circuit can be determined at DC point only. This circuit can be solved using…

Q: 3. A full-wave zero-current switching quasi-resonant boost converter is operated at the following…

A: Step 1:Given:Input voltage Vs=48VS​=48 VOutput voltage Vo=60Vo​=60 VSwitching frequency f=0.6fs​=0.6…

Q: state how the Direct coupled amplifier differs from the RC coupled and Transformer coupled…

A: Direct coupled amplifier- it is directly connecting output of one transistor with the input of the…

Q: What Is frequency modulation and demodulation? Describe their importance and how they work.

A: Given: Frequency modulation and demodulation

Q: In digital frequency meter, output of amplifier is applied to the.....

A: A computerized recurrence meter is an electronic instrument that can quantify even the more modest…

Q: Draw the transfer curve of logarithmic amplifier.Explain how does a chopper work with basic circuit…

A: Answer: given that  To find the transfer curve of logarithmic amplifier

Q: . Draw the d.c load line for the circuit diagram shown below. What will be the Q point if zero…

A: Redrawing the above circuit with proper markings: To draw the DC load line of the PNP Transistor we…

Q: Find the following: DC gain, inductor current ripple and output voltage ripple:   For DC-DC Buck…

A: Types of Basic DC-DC Converters Buck Converter Boost Converter Buck Boost Converter

Q: 2. Determine the drift in the Q-point for the two biasing circuits and therefore compare their bias…

A: 1. Fixed bias circuit -  The fixed bias circuit diagram is shown below, The circuit presented is…

Q: Why are coupling capacitors often used to connect the signal source and the load to amplifier…

A: The main reason to use coupling capacitors is to give a route for the ac component and the other…

Q: Using LTSpice, simulate the circuit below, use 2N3904 for the transistor. Part! DC simulation:…

A:

Q: What is the function of coupling capacitors? Assuming that they are performing their intended…

A: In amplifiers, it is sometimes required to have only an AC signal at the output for an example audio…

Q: Discuss the effect of increasing inductor filter capacitor on the output voltage and current.

A: A capacitor that filters a specific frequency or frequency range from a circuit is known as a…

Q: 5, a) Determine Vdsat when ID=.5 mA. b) Determine Kn when ID = 0.5 Amps. (Show your work!) c)…

A:

Q: (a) Draw the equivalent circuit used for ac analysis of the circuit shown .      (Use transistor…

A: Given: (a) Draw the equivalent circuit used for ac analysis of the circuit shown. On assume all…

Q: Determine the gain margin and phase margin for a system that gave  the following open-loop…

A: Given system has open loop experimental frequency response data a) At frequency =0.004 Hz  a gain of…

Q: (a) Draw the equivalent circuit used for ac analysis of the circuit shown .      (Use transistor…

A:

Q: Find the resonance point and the half-width of the speed versus frequency curve for the damped…

A: When b / m << 2ω0 (half width of speed), we say that the oscillator is lightly damped. For a…

Q: Q9. Draw Zener regulator circuit to obtain regulated DC voltage 6.8 V. Considering input DC voltage…

A:

Q: In an ac transistor amplifier, the circuit includes capacitors as well as  resistors. What is the…

A: Transistor amplifier

Q: What can you say about the current characteristic for both the series and parallel circuit at…

A:

Q: One way to control power, in an electronic system is to using the PWM (pulse width modulation)…

A: According to the question, we need to draw the output waveform for the given circuit

Q: 5. What is the approximate frequency of the modulating signal having a bandwidth of 15 kHz and a…

A: In this question we will find frequency of modulating signal with help of bandwidth and frequency…

Q: With an aid of a. c. equivalent circuit, derive an equation representing common- mode gain (Ac) of…

A: To derive an equation representing the common-mode gain of a circuit using the AC equivalent…

Q: Draw a schematic diagram of a full-wave bridge power supply.

A: Full wave bridge convert Alternating input to DC output which is used as the input source for…

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.